Weed Eater 180083 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse, Engine

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 27)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 27

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 28)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

 

GOVERNOR

GOVERNOR

 

CONTROL

 

CONTROL LEVER

 

PLATE

 

 

HOLES “A”

CLAMP

THROTTLE

 

SCREW

CABLE

 

 

FIG. 28

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. WE1538A II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsGeneral Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE1538A SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 140044X428 Optional Equipment 170551 Control Th/ch Flag Seat LBD48 DecalsWheels & Tires LSB42Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

180083 specifications

The Weed Eater 180083 is a powerful and efficient string trimmer designed for homeowners and landscaping professionals alike. Known for its reliability and user-friendly design, this trimmer has become a popular choice for those seeking to maintain their lawns and gardens with ease.

One of the standout features of the Weed Eater 180083 is its lightweight construction, which makes it easy to maneuver around flower beds, trees, and other obstacles in the yard. Weighing less than some competing models, this trimmer reduces user fatigue, allowing for extended use without sacrificing comfort.

The Weed Eater 180083 is powered by a robust 18V battery system, ensuring that users have plenty of runtime to tackle their trimming tasks. This cordless design not only enhances portability but also eliminates the hassle of dealing with gas or tangled cords. The lithium-ion battery technology provides consistent power and performance, allowing for reliable operation from start to finish.

Another key feature of the Weed Eater 180083 is its adjustable cutting width. Users can choose between different cutting widths, enabling them to navigate narrow spaces or cover wider areas as needed. Its automatic line feed system ensures that the trimmer line replenishes itself as you work, minimizing downtime and keeping the focus on efficient trimming.

The trimmer's ergonomic handle design provides a comfortable grip, reducing strain on the hands and wrists during prolonged use. Additionally, the Weed Eater 180083 is equipped with a safety guard to protect the user from debris and potential hazards, ensuring a safer working experience.

In terms of maintenance, the Weed Eater 180083 is designed for easy line replacement and overall upkeep. The user-friendly design means that even those unfamiliar with string trimmers can quickly learn how to manage and maintain the equipment effectively.

Overall, the Weed Eater 180083 combines advanced engineering with practical features that make it a standout choice for anyone looking to keep their outdoor spaces neat and tidy. With its blend of power, efficiency, and user-friendly attributes, the Weed Eater 180083 is a valuable tool for all gardening enthusiasts.
Top Page Image Contents