Weed Eater 177677 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

CAUTION: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place gearshift lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key “OFF” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TO REMOVE MOWER (See Fig. 15)

Mower will be easier to remove from the right side of tractor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and lift clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRAC- TOR, REMOVE THE FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 15)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with discharge guard to right side of tractor.

•Lower lift lever to its lowest position.

•Install mower in reverse order of removal instructions.

 

 

SQUARE HOLE

SMALL RETAINER SPRING

 

SUSPENSION ARMS

 

ENGINE PULLEY

 

 

CLUTCH SPRING

 

FRONT LINK

 

 

RETAINER SPRING

 

 

ANTI-SWAY BAR

 

RETAINER SPRINGS

COLLAR

 

 

(BOTH SIDES)

HOUSING GUIDE

LARGE

 

RETAINER

BRACKET

 

 

SPRING

 

FIG. 15

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. WE16542D II. Slope Operation Safety RulesIV. Service General OperationTable of Contents Customer Responsibilities Product SpecificationsSteering Wheel Seat Unassembled PartsKeys Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTowing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To TransportADD Gasoline Mowing TipsTo Start Engine See Fig Before Each USE Lubrication ChartCustomer Responsibilities General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE16542D SchematicElectrical KEY Part NO. NO.DESCRIPTION Chassis and Enclosures KEY Part Description Drive 72140608 Steering Assembly KEY Part NO. NO.DESCRIPTION Spark Arrester Optional Equipment174642 Seat Assembly Wheels & Tires DecalsMower Lift Nut Lock w/Wsh 1/2-13 Unc Mower Deck Repair Parts Service Notes Limited Warranty For Limited WarrantiesSlope Sighting Guide CUT This OUT Dotted Is a
Top Page Image Contents