HOW to Start Your Unit, Operating Position

Engine Choke Lever

ON/STOP

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger.

NOTE: If engine dies with the choke le- ver in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to OFF CHOKE.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING INSTRUCTIONS

OPERATING POSITION

ALWAYS WEAR:

Eye Protection

Long Pants

Muffler	Heavy Shoes

Primer Bulb

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

Cut from your right to your left.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting.

To stop engine:

SRelease the throttle trigger.

S Push and release the engine ON/STOP switch.

530086929 specifications

The Weed Eater 530086929 is a standout among outdoor power tools, specifically designed to provide efficient and effective trimming and edging solutions for homeowners and landscaping professionals alike. This powerful tool is engineered with an array of features and technologies that enhance its functionality and ease of use.

One of the most notable characteristics of the Weed Eater 530086929 is its robust line of power. This trimmer is equipped with a reliable engine that delivers ample torque and speed, allowing users to tackle tough grass and weeds effortlessly. Its lightweight design ensures that users can maneuver it easily, reducing fatigue during extended use and making it suitable for larger yards as well.

The Weed Eater 530086929 features a bump-feed line advancement system, which allows for simple and quick line reloading. Instead of fumbling with manual adjustments, users can easily tap the trimmer head against the ground, automatically feeding more line as needed. This technology not only saves time but also enhances productivity, allowing users to focus on their trimming tasks without interruptions.

Moreover, this model includes an adjustable cutting width feature that offers versatility depending on the job at hand. Users can choose a wider cutting path for clearing larger areas or switch to a narrower setting for precision work around flower beds and fences. This adaptability makes it a practical choice for managing various landscaping tasks.

The ergonomic design of the Weed Eater 530086929 is another key advantage. The handle is designed for comfort, providing a secure grip that helps maintain control even during prolonged periods of use. Coupled with its balanced weight distribution, the trimmer allows for smooth operation, whether you are trimming on flat surfaces or working in more challenging terrain.

Furthermore, the Weed Eater 530086929 utilizes an advanced vibration damping technology, which significantly reduces hand and arm fatigue. This feature is particularly important for users who need to operate the trimmer for extended periods, ensuring that they remain comfortable and focused on their work.

In conclusion, the Weed Eater 530086929 combines power, versatility, and comfort in one efficient package. With its innovative features, dependable performance, and user-friendly design, this trimmer is an excellent investment for anyone looking to maintain their outdoor spaces with ease and effectiveness. Whether for routine lawn care or tackling overgrown areas, the Weed Eater 530086929 meets the demands of any trimming job with confidence.