HOW to Start Your Unit, Operating Position

HOW TO START YOUR UNIT

Starting Position Choke Lever

Trigger
Primer Bulb	Muffler
	Muffler

WARNING: The trimmer head will turn while starting the engine. A hot muffler can cause serious burns.

COLD ENGINE STARTING OR STARTING AFTER REFUELING

SSet unit on a flat surface.

SSlowly press the primer bulb 6 times.

SMove choke lever to FULL CHOKE position. S Squeeze the throttle trigger fully and hold

through all remaining steps.

S Pull starter rope handle sharply 6 times. S Move choke lever to HALF CHOKE position. S Pull starter rope handle no more than 6

pulls, until engine runs.

S Allow engine to run 10 seconds, then move choke lever to OFF CHOKE position.

RESTARTING A WARM ENGINE

SMove choke lever to OFF CHOKE position. S Pull starter rope handle until engine runs. S If engine does not start in 5 pulls, follow instructions in STARTING A COLD ENGINE.

For occasional use only.

OPERATING POSITION

ALWAYS WEAR: Eye

Protection

Long Pants

Heavy Shoes

Cut from your right to your left.

ADVANCING THE CUTTING LINE

Advance line by tapping the bottom of the cutting head lightly on the ground while engine is running at full speed. A metal blade attached to the shield will cut the line to the proper length.

REPLACING THE LINE

S Remove spool by firmly pulling on tap button.

SClean entire surface of hub and spool.

S Replace with pre--wound spool, or cut a length of 18 feet of .065” (1.6 mm) diameter Weed Eater! brand line. Never use wire, rope, string, etc., which can break off and become a dangerous missile.

SInsert one end of line about 1/2 inch (1 cm)

into the small hole on the inside of the spool. S Wind line evenly and tightly onto spool.

Wind in the direction of the arrow on the spool.

SPush the line into the notch, leaving 3 to 5

inches ( 7 -- 12 cm) unwound.

SInsert the line into the exit hole in the hub as

shown in the illustration.

SAlign the notch with the line exit hole.

SPush spool into hub until it snaps into place. S Pull the line extending outside of the hub to

release it from the notch.

Small

HoleSpool

Line in Notch

Hub

Line exit hole

We recommend all service and adjustments not listed in this manual be performed by an Authorized Service Dealer.

CARBURETOR ADJUSTMENTS

Your carburetor is equipped with limiter caps. Adjusting the carburetor is a complicated task. We recommend that you take your unit to an Authorized Service Dealer. Damage will occur if you turn the needles beyond the limiter stops.

IGNITION TIMING

The ignition timing is fixed, non--adjustable.

SPARK PLUG

Replace the spark plug yearly using a Champion RCJ--8Y plug. Spark plug gap is

.025”.

530087310 specifications

The Weed Eater 530087310 is a powerful and versatile string trimmer designed to handle various outdoor trimming tasks with ease. Known for its reliability and performance, this tool is a favored choice among homeowners and landscaping professionals alike. The 530087310 model stands out due to its robust features and advanced technology, making it an essential addition to any lawn care arsenal.

One of the standout features of the Weed Eater 530087310 is its lightweight design, which enhances maneuverability and reduces user fatigue during extended use. Weighing at just under 10 pounds, it allows users to reach tight spaces and tackle overgrown areas without straining their arms or back. The ergonomic handle is designed for comfort, ensuring a secure grip that minimizes vibrations, allowing for prolonged operation without discomfort.

Equipped with a reliable 22cc two-cycle engine, the 530087310 delivers sufficient power to cut through thick grass and weeds. The engine is engineered for efficient fuel consumption, providing users with a longer runtime between refuels. This not only improves productivity but also makes the trimmer more cost-effective over time.

The trimmer utilizes a dual-line system featuring a semi-automatic feed which allows for easy reloading of the line as it wears down. This convenience ensures that the user can maintain a continuous trimming workflow without the hassle of manual line adjustments. The cutting width of the 530087310 is 17 inches, striking a perfect balance between efficiency and control, making it suitable for both small yards and larger landscaping projects.

One of the key technologies integrated into the Weed Eater 530087310 is the Easy Start system, designed to make starting the engine a breeze, even after periods of inactivity. This feature reduces the initial resistance when pulling the starter cord, making it accessible for users of all experience levels.

Furthermore, the Weed Eater 530087310 is designed with durability in mind. Manufactured with high-quality materials, it can withstand the rigors of frequent use and harsh outdoor conditions. Coupled with a straightforward maintenance routine, this trimmer ensures longevity and ongoing performance.

In summary, the Weed Eater 530087310 is a well-rounded string trimmer that delivers power, comfort, and convenience. With its user-friendly features and reliable engine performance, it is an excellent choice for anyone looking to maintain a pristine lawn or garden with minimal effort. Whether trimming along edges or tackling tough weeds, the 530087310 is equipped to handle it all.