McCulloch MCT2024 user manual Save These Instructions, Safety Precautions, International Symbols

Page 3

2 - SAFETY PRECAUTIONS

2 - SAFETY PRECAUTIONS

PLEASE READ - SAVE THESE INSTRUCTIONS

When using an electrical power tool, basic precautions should always be followed to assure maximum safety and optimum performance. Read this manual before assem- bling and operating this power tool. Failure to comply with instructions may result in electrical shock, burns, fire, or personal injury.

MINIMUM WIRE GAUGE RECOMMENDATIONS

VOLTS

EXTENSION CORD

WIRE SIZE

LENGTH

REQUIRED

 

 

25 feet / 7.5m

18 A.W.G.*

120

50 feet / 15m

16 A.W.G.*

 

100 feet / 30m

16 A.W.G.*

*American Wire Gauge

Table 1

12. USE POWER TOOL CORRECTLY - Use this power

tool only for its intended use as described in this

manual. DO NOT SWEEP WITH TRIMMER -

Sweeping refers to tilting stringhead to sweep away

debris from walkways, etc. Your trimmer is a powerful

tool and small stones or other such debris may be

hurled 50 feet or more, causing injury or damage to

nearby property such as automobiles, homes and

windows. Inspect area before starting the power tool

2-2. EXPLANATION OF NOTE, WARNING, and WARRANTY SYMBOL

1.

A NOTE is used to convey additional information, or

 

highlight a particular explanation, or to expand a step

 

instruction.

2.

A WARNING identifies a procedure which, if not

 

undertaken or if improperly done, can result in a seri-

 

ous personal injury or damage to the unit and/or

 

both.

WARNING

2-1. TO REDUCE THE RISK OF ELECTRIC SHOCK, BURNS, FIRE OR PERSONAL INJURY:

1. FOLLOW ALL SAFETY INSTRUCTIONS listed in

 

this manual before/during operation of this trimmer.

2.

TO REDUCE THE RISK OF ELECTRIC SHOCK this

 

power tool has a polarized plug (one blade is wider

 

than the other). This plug will fit in a polarized outlet

 

only one way. If the plug does not fit fully in the out-

 

let, reverse the plug. If it still does not fit, contact a

 

qualified electrician to install the proper outlet. Do not

 

change the plug in any way.

3.

INSPECT UNIT FOR DAMAGE to the housing, cord

 

or plug. Keep all fasteners tight. Do not use if the

 

switch does not turn the unit off properly. Never use

 

unit if cord or plug has been damaged, the motor or

 

unit itself is not working as it should or has been

 

dropped, damaged, left outdoors or dropped in

 

water. Never operate with any air opening blocked.

 

Keep air openings free of debris that may reduce air

 

flow. Replace damaged parts that are chipped,

a.When using the power tool, an extension cord of adequate size must be used for safety and to prevent loss of power and overheating.

b.The extension cord must be specifically intended for outdoor use and marked “SJ” or “SJT” and with the suffix “WA”. In Canada, the extension cord must be marked “SFTW”.

c.Inspect extension power cord for loose or exposed wires and damaged insulation. If damaged, replace before using power tool.

DO NOT ABUSE CORD - Never carry power tool by cord or pull cord to disconnect from outlet. Keep cord clear of operator and obstacles at all times. Do not expose cord to heated surfaces, oil or water. Do not pull cord around sharp edges, corners or close door on cord.

6.NO SERVICEABLE PARTS INSIDE - Your dou-

ble insulated power tool has no serviceable parts inside. Do not attempt to repair it yourself. For service information, contact the McCulloch Product Service Department listed on the back cover of this User Manual.

 

to remove debris and other objects that can cause

 

damage during operation.

13.

DO NOT USE ACCESSORIES or attachments

 

except as recommended and provided by McCulloch.

 

Do not use any type of wire or metal cutting line.

14.

DO NOT OVERREACH - Keep firm footing and bal-

 

ance at all times.

15.

AVOID UNINTENTIONAL STARTING - Do not carry

 

plugged in trimmer with your finger on the switch.

16.

DISCONNECT trimmer from power supply when not

 

in use and before servicing stringhead.

17.

STORE trimmer indoors. Appliance should be stored

 

in a dry, high or locked up place - out of the reach of

 

children.

18.

Don’t grasp the exposed cutting blades or cutting

 

edges when picking up or holding the power tool.

19.

Do not force appliance - it will do the job better and

 

witth less likelihood of a risk of injury at the rate for

 

which it was designed.

3.

(WARRANTY SYMBOL) serves notice that

unless instructions or procedures are followed, any damage will void the warranty and repairs will be at owner’s expense. Service other than user mainte- nance should be performed by a McCulloch Authorized Service Center. Damage or conditions caused by improper maintenance practices which render this product inoperable will void the manufac- turer’s warranty.

4.FOR WARRANTY OR SERVICE contact the nearest McCulloch Authorized Service Center.

2-3. INTERNATIONAL SYMBOLS

1.Read the User Manual (Figure 2-1).

2.Use of these personal safety items is highly recom- mended to reduce the risk of accidental injury (Figure 2-2).

SAVE THESE

INSTRUCTIONS

 

cracked or damaged in any way.

4.

DOUBLE INSULATED to help protect against

 

electric shock. Double insulation construction

consists of 2 separate “layers” of electric insulation. power tool built with this insulation system are not intended to be grounded. As a result, the extension cord used with your unit can be plugged into any conventional 120 volt electrical outlet. Normal safety precautions must be observed when operating an electrical power tool. The double insulation system is only for added protection against injury resulting from a possible internal electrical insulation failure.

5.EXTENSION CORD - Use only with an extension cord intended for outdoor use. Match wire gauge to the cord length. See table below. A 2-wire cord with- out a ground connection may be used since this power tool is double insulated. If in doubt of proper wire size, use the next heavier gauge. Please note that the smaller the gauge number, the heavier the cord.

7.RISK OF EYE INJURY - Always wear goggles or other suitable eye protection when operating your trimmer. Edging increases the risk of injury caused by flying debris. Always keep bystanders at a safe distance.

8.KEEP HANDS AND FEET AWAY from rotating line. Do not operate without guard attached.

9.DRESS PROPERLY - Always wear long pants, shoes and gloves. Do not wear loose clothing, jewel- ry, short pants, sandals or go barefoot.

10.KEEP AREA CLEAR - Keep everyone, especially children and pets away from the area of operation. Turn off unit immediately if you are approached.

Never allow children to operate the appliance to be used as a toy or to run unattended at any time.

11.AVOID A DANGEROUS ENVIRONMENT - Do not use in the presence of flammable liquids or gases, smoking or burning materials to avoid creating a fire or explosion. Never operate the trimmer in wet or damp conditions or around swimming pools, hot tub, etc. Do not use in rain. Do not handle plug, cord or appliance with wet hands.

4

Use of these personal safety items is highly recommended to reduce the risk of accidental injury.

Read the User Manual.

2-1

2-2

 

 

 

5

Image 3
Contents USA AltoSpecifications IntroductionGeneral Information Safety Precautions International SymbolsSave These Instructions Connect the Cord Assembly InstructionsAssembly Debris Shield InstallationTAP Operating Insyructions Maintenance InstructionsStand AS Shown -1 and Check the Following Extending the LineMaintenance ONE Year Limited Warrnaty Caracteristiques GeneralitesAvertissement Measures DE SecuriteAucune Pièce Interne Nest Measures DE Securite Instructions Pour Montage Conserver CES InstructionsAvance DE LA Ligne DE Coupe Instructions Pour Montage Instructions D’UTILISATIONDemarrage SE Tenir Debout Comme Indiqué -1 ET Vérifier CE QUI SuitEntretien Remplacement DE LA Bobine DE FIL DE NylonEntretien Maintenance Instructions Garantie Limitée DE UN AnnéeFavor DE Leer IntroduccionRenseignments Generaux Precautiones DE Seguridad AdvertenciaEspecificaciones Conserve Estas Instrucciones Explicacion DE NOTA, Adverten CIA Y Simbolo DE GarantiaSimbolos Internacionales Conectar EL Cable Instrucciones DE EnembladoArmado Instalación DE LA Guarda PRO- TectoraSustitución DEL Carrete DEL Cable DE Nylon Instrucciones DE Operacion Instrucciones DE MaintenimientoMostrada -1 Y Revise LO Siguiente GolpeeMaintenimiento PrecaucionGarantía Limitada DE UN AÑO MCT2024

MCT2024 specifications

The McCulloch MCT2024 is a versatile and efficiently designed chainsaw that caters to both amateur and professional users. Renowned for its powerful performance and user-friendly features, the MCT2024 is an excellent choice for various cutting tasks, from tree felling to branch trimming.

One of the standout features of the MCT2024 is its robust 2.4 kW engine, which provides a reliable and ample power output for challenging jobs. This engine is designed to ensure optimal performance while maintaining fuel efficiency, making this chainsaw a cost-effective option for extended use. The chainsaw's lightweight design further enhances its usability, allowing users to maneuver it easily, even during lengthy sessions.

The MCT2024 employs advanced technologies to improve both safety and performance. The chainsaw includes a low-kickback bar and chain, which significantly reduces the risk of the saw jumping back during operation. This feature makes the MCT2024 incredibly safe for inexperienced users, while also providing confidence for experienced operators. Moreover, the tool is equipped with an automatic oiling system, which ensures that the chain remains lubricated during use. This feature enhances the life of the chain and bar and maintains optimal performance levels.

Another notable characteristic of the McCulloch MCT2024 is its ergonomic design. The chainsaw features a comfortable grip and a well-balanced construction, reducing user fatigue and enabling prolonged usage without discomfort. Its quick-release air filter allows for easy maintenance and cleaning, ensuring that the chainsaw remains in peak condition over time.

Additionally, the MCT2024 incorporates a tool-free chain tensioning system, making it simple and straightforward to adjust chain tension as needed. This allows users to focus on their cutting tasks rather than getting bogged down by complicated adjustments.

In summary, the McCulloch MCT2024 is an impressive chainsaw that combines power, safety, and ease of use. With its powerful engine, automated oiling, ergonomic design, and user-friendly features, it stands out as an exceptional tool for a wide range of cutting applications. Whether you are a seasoned professional or a casual user, the McCulloch MCT2024 promises reliable performance and satisfaction with every use.