McCulloch M17538H manual Engine continues

Page 28

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

CORRECTION

 

Engine continues

1.

Faulty operator-safety presence control

1.

Check wiring, switches and connections. If not

 

to run when oper-

 

system.

 

corrected, contact an authorized service center/

 

ator leaves seat

 

 

 

department.

 

 

 

 

 

 

with attachment

 

 

 

 

 

clutch engaged

 

 

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

 

2.

Mower deck not level.

2.

Level mower deck.

 

 

3.

Buildup of grass, leaves, trash under mower.

3.

Clean underside of mower housing.

 

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

 

5.

Clogged mower deck vent holes from

5.

Clean around mandrels to open vent holes.

 

 

 

buildup of grass, leaves, and trash around

 

 

 

 

 

mandrels.

 

 

 

Mower blades will

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

 

not rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

 

 

Poor grass

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

discharge

2.

Travel speed too fast.

2.

Shift to slower speed.

 

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

 

4.

Mower deck not level.

4.

Level mower deck.

 

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

 

6.

Worn, bent or loose blade.

6.

Replace blade. Tighten blade bolt.

 

 

7.

Buildup of grass, leaves, trash under mower.

7.

Clean underside of mower housing.

 

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

 

10.

Improper blades used.

10.

Replace with blades listed in parts manual.

 

 

11.

Clogged mower deck vent holes from buildup

11.

Clean around mandrels to open vent holes.

 

 

 

of grass, leaves, trash around mandrels.

 

 

 

Headlight(s) not

1.

Switch is “OFF”.

1.

Turn switch “ON”.

 

working

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

(if so equipped)

3.

Faulty light switch.

3.

Check/replace light switch.

 

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

 

 

Battery will not

1.

Bad battery cell(s).

1.

Replace battery.

 

charge

2.

Poor cable connections.

2.

Check/clean all connections.

 

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

 

2.

Debris on steering plate (if equipped).

2.

See "CLEANING" in the maintenance section.

 

 

3.

Motion drive belt worn, damaged, or broken.

3.

Replace motion drive belt.

 

 

4.

Air trapped in transmission during

4.

Purge transmission.

 

 

 

shipment or servicing.

 

 

 

 

5.

Axle key missing.

5.

Install axle key at rear wheel. See "TO REMOVE

 

 

 

 

 

WHEEL" in the Service and Adjustments section.

 

 

 

 

 

 

 

Engine "back-

1.

Engine throttle control not set between

1.

Move throttle control between half and full speed

 

fires” when turn-

 

half and full speed (fast) position before

 

(fast) position before stopping engine.

 

 

stopping engine.

 

 

 

ing engine “OFF”

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Engine dies when

1.

Reverse operation system (ROS) is not "ON"

1.

Turn ignition key to ROS "ON" position. See

 

tractor is shifted

 

while mower or other attachment is engaged.

 

Operation section.

 

into reverse

 

 

 

 

 

 

 

 

 

 

 

28

Image 28
Contents OPERATOR’S Manual Model NO. M17538H Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To Check Battery See FigCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To SET Parking Brake See FigTo USE Throttle Control D See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig Reverse Operation System ROSTo Operate Mower To Stop Mower BladesBefore Starting the Engine To TransportTowing Carts and Other Attachments Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigTransaxle Maintenance EngineTransaxle Pump Fluid LubricationCleaning Clean AIR ScreenAIR Filter MufflerDeck Washout Port See Fig To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Belt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Belt Drive See FigTransaxle Motion Control Lever NEU- Tral Adjustment See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig Front Wheel TOE-IN/CAMBERTo Adjust Steering Wheel Alignment To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX12.29.09 JA