McCulloch 250 B instruction manual Troubleshooting Table Cause Remedy

Page 15

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing all of the recommended remedies below except remedies that require operation of the unit.

TROUBLE

CAUSE

REMEDY

Engine will not

1. ON/STOP switch in STOP

1.

Move ON/STOP switch to ON

start.

 

position.

 

position.

 

2. Engine flooded.

2.

See “Starting a Flooded Engine” in

 

3. Fuel tank empty.

 

Operation Section.

 

3.

Fill tank with correct fuel mixture.

 

4. Spark plug not firing.

4.

Install new spark plug.

 

5. Fuel not reaching

5.

Check for dirty fuel filter; replace.

 

 

carburetor.

 

Check for kinked or split fuel line;

 

6. Carburetor requires

 

repair or replace.

 

6.

Contact an authorised service dealer.

 

 

adjustment.

 

 

Engine will

1. Carburetor requires

1.

See “Carburetor Adjustment” in

not idle

 

adjustment.

 

Service and Adjustments Section.

properly.

2. Crankshaft seals worn.

2.

Contact an authorised service dealer.

 

3. Compression low.

3.

Contact an authorised service dealer.

Engine will not

1.

Air filter dirty.

1. Clean or replace air filter.

accelerate,

2. Spark plug fouled.

2. Clean or replace plug

lacks power,

3.

Carburetor requires

 

and regap.

or dies under

3. Contact an authorised service dealer.

a load.

4.

adjustment.

4. Contact an authorised service dealer.

 

Carbon build-up on

 

 

muffler outlet screen.

 

 

 

5.

Compression low.

5. Contact an authorised service dealer.

Engine

1.

Choke partially on.

1.

Adjust choke.

smokes

2.

Fuel mixture incorrect.

2.

Empty fuel tank and refill with

excessively.

3.

Air filter dirty.

 

correct fuel mixture.

 

3.

Clean or replace air filter.

 

4.

Carburetor requires

4.

Contact an authorised service dealer.

 

 

adjustment.

 

 

Engine runs

1. Fuel mixture incorrect.

1. Empty fuel tank and refill with

hot.

2. Spark plug incorrect.

 

correct fuel mixture.

 

2. Replace with correct spark plug.

 

3. Carburetor requires

3. Contact an authorised service dealer.

 

 

adjustment.

 

 

 

4. Carbon build-up on

4. Contact an authorised service dealer.

 

 

muffler outlet screen.

 

 

15

Image 15
Contents Manuel D’INSTRUCTIONS BetriebsanweisungManual DE Instrucciones Primer bulb Identification What is WHAT?Safety Rules Identification of SymbolsOperator Safety Unit / Maintenance SafetyTrimmer use Assembly Attaching Shoulder Harness Clamp Shoulder Harness AdjustmentAssembly of Shoulder Harness Attaching the HandlebarAttaching the Plastic Shield and Trimmer Head Configuring Your UnitAssembly Information Trimmer Head Assembly Information Weed BladeAttaching the Metal Shield Installation of the Metal BladeFueling Engine HOW to Stop Your UnitHOW to Start Your Unit OperationOperating Instructions for USE with Trimmer Head Starting a Warm EngineStarting a Flooded Engine Operating PositionCm above ground Cutting MethodsOperating Instructions for USE with Weed Blade Cutting Work areaCheck for Damaged or Worn Parts MaintenanceInspect and Clean Unit and Labels Check for Loose Fasteners and PartsReplacing the Line Service and AdjustmentsClean AIR Filter Replace Spark PlugStorage Troubleshooting Table Cause Remedy EC Declaration of Conformity Only applies to Europe Declaration of ConformityTechnical Data Sheet Without cutting attachment or shield, empty tank, kgIdling, m/s Racing, m/s