Sears 917.2565 manual Service a, Justments, Engine, To Adjust Throttle Control Cable

Page 24

SERVICE A

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

(See Fig. 27)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

With engine not running, move throttle control lever from slow (,_) to choke (XI) position. Slowly move lever from choke (N) to fast (_) post on.

Check that holes "A" in governor control lever and hole in governor plate line-up, If holes 'W'are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

GOVERNOR

GOVERNOR

CONTROL LEVER

CONTROL PLATE

\

 

/

HOLES "A"

CLAMP

THROTTLE

 

SCREW

CABLE

 

FaG. 27

 

AJUSTMENTS

FINAL SETTING *

,Start engine and allow to warm for five minutes. Make fina! adjustments with engine running and shift/motion control lever in neutral (N) position.

*Move throttle control lever to slow (,_!) position, With finger, rotate and hold throttle lever against idle speed screw, Turn idle speed screw to attain 1750 RPM,

,While still holding throttle lever against idle speed screw, turn idle mixture valve in (clockwise) until en- gine begins to die and then turn out (counterclockwise) until engine runs rough. Turn valve to a point midway between those two positions. Release throttle lever.

ACCELERATION TEST -

Move throttle control lever from slow (,_!,) to fast (,_) position. If engine hesitates or dies, turn idle mixture

valve out (counterclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until engine acceler- ates smoothly.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WiTH THE ENGINE

GOVERNOR, WHICH iS FACTORY SET FOR PROPER

ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE

THE FACTORY HIGH SPEED SETTING CAN BE

DANGEROUS. IF YOU THtNKTHE ENGINE-GOVERNED

HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

NEAREST AUTHORIZED SERVICE CENTER/

DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND

EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

THROTTLE

iDLE SPEED

LEVER

SCREW

TO ADJUST CARBURETOR (See Fig. 28)

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjust- ment may be required to compensate for differences infuel, temperature, altitude or load. if the carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in (clockwise) de- creases the supply of fuel to the engine giving a leaner fuel/ air mixture. Turning the idte mixture valve out (counter-

clockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture.

#_PORTANT: DAMAGE TO THE NEEDLE VALVE AND

THE SEAT IN CARBURETOR MAY RESULT IF SCREWIS TURNED IN TOO TIGHT.

iDLE M_XTURE VALVE

PRELIMINARY SETTING -

FIG. 28

 

Air cleaner assembly must be assembled to the carbu- retor when making carburetor adjustments.

oBe sure the throttle control cable is adjusted properly (see above).

oWith engine off turn idle mixture valve in (clockwise) dosing it finger tight and then turn out (counterclock° wise) 1 full turn.

24

Image 24
Contents For Consumer Assistance HOT LINE, Call this Toll Free Number IIIIIIIIIIIIIIiiiIIIIIIIIIIIIIIIlL Children Exhaust from this product conTains chemicals known to the State of Califor Nia to cause cancer, birth defects, or otherMaintenance Agreement LBM TED TWO Year Warranty on Craftsman Rmding EquipmentLimited 90 DAY Warranty on Battery Customer Responsibimt ESCont Accessories AN Attachme TS Engine MaintenancePerformance Parts Bag contents shown full size Conte TS of HA PackTools Required for Assembly To Remove Tractor from CartonBefore Rolung Tractor OFF Skid Unpack CartonAsse BLY Checkmst Check T1RE PressureCheck Deck Levelness Check for Proper Positon of ALL BeltsOperatio LockOperation Know Your TractorFIGo HOW to USE Your Tractor To Adjust Mower Cutting HeightOpera To Operate Mower See Fig To Operate on HillsTo Transport Check Engine OiL Level See FigADD Gasoune To Start Engne See FigWipeoffany Do not Store, spill or Use gasoline near an open flameCustom Espons Lines General RecommendationsLubrication To Clean Battery and Terminals Custo Respon IL ESBrake Operatmon Blade Removal See FigOustome Espons EngneTransaxle Cooling AIR Filter See FigCleaning CustomeilitiMuffler Spark PlugsTo iNSTALL Mower See Fig Ervice a ADJ StmentsService AN Adjustments To Level Mower HousingRG. !7 Both Front LItNKSMUST be Equal in LengthErvice Adjustments To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigService AN AdjustmentsTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERService and Adjustments Wiring, SeeTo Replace Headlight Bulb Interlocks and RelaysService a To Adjust Throttle Control CableTo Adjust Carburetor See Fig JustmentsStorage OtherProblem Cause Correction PlugTrou Leshooting Points CausecorrectionService Note Schematic Ignition SwitchTractor = Model Number Tractor =-. Model Number ElectricalElectrical KEY PartNO. NO= DESCRiPTiON Chassis and Enclosures KEY Part Description MODELNUMBER9!7,256,00 Drive KEYDESCRiPTiON Lt/YtSteering Assembly Tractor - Model NumberSteering Assembly NO. noDescrbpton Fitting GreaseOptional Equipment 40338113 Engine TyttSeat Assembly KEY Part DescriptionKEY Part Decals Wheels & TiresKEY Part NO, no LiFT 3219Tractor - Model Number 9!7.256500 KEY Part NO, NO.DESCRIPTIONTractor -- Model Number MowerTractor == Model Number MowerPart Description Dana Transaxle Model Number Dana Transaxle = Model Number KEY Part NO. noBriggs & Stratton Engine Model Number 28R707 Type Number 634A 3O8306 125 130 147 137 127 284I525 535 224240 265 209 601 305 1044 455Briggs & Stratton Engine Model Number 28R707, Type Number 1090311 FiEPAJR Parts Briggs & Stratton Enghne Model Number 28R707, Type NumberBRtGGS & Stratton Engine =MODEL Number 28R707, Type Number Included in bothService Otes ZO Oz Model Number = Engine Model NO. 28R707, Type no Part Number Part Description

917.2565 specifications

The Sears 917.2565 lawn tractor is a versatile and reliable piece of garden equipment that has made a name for itself among homeowners and gardening enthusiasts alike. Designed for ease of use and efficiency, this tractor combines a robust construction with a host of innovative features that elevate it within its class.

One of the standout characteristics of the Sears 917.2565 is its powerful engine. Equipped with a 17.5 horsepower Kohler engine, this tractor is designed to tackle the toughest lawn care jobs with ease. The engine provides ample power to drive the tractor and its attachments, making it suitable for larger properties or extensive landscaping tasks.

The cutting deck is another impressive feature of the Sears 917.2565. With a 42-inch reinforced deck, it delivers a clean and even cut, ensuring your lawn looks pristine after mowing. The cutting height is adjustable, allowing users to choose from multiple settings to suit various grass types and conditions. This flexibility makes it easier to maintain the lawn's health and appearance.

In terms of technologies, the Sears 917.2565 incorporates a smooth hydrostatic transmission system. This technology provides seamless speed adjustments without the need for manual gear shifting, offering a user-friendly experience. Whether navigating tight corners or cruising across open spaces, the hydrostatic transmission allows for easy maneuverability.

Comfort is also a priority in the design of the Sears 917.2565. The tractor features a comfortable, adjustable seat designed for extended use. The ergonomic layout of the controls ensures that everything is within easy reach, which adds to the overall user experience.

Additionally, this model offers versatility through various attachments like baggers, mulchers, and tow-behind accessories. Homeowners can customize their tractors to meet their specific lawn care needs, making it a valuable addition to any garden equipment arsenal.

Overall, the Sears 917.2565 combines power, efficiency, and comfort. Its rugged construction and modern technologies make it suitable for both residential lawns and more significant landscaping projects, ensuring it remains a popular choice in the realm of lawn maintenance.