Sears 917.252714 manual To Replace Mower Blade Drive Belt, To Adjust Brake See Fig, Belt Removal

Page 23

SERVICE AND

TO REPLACE MOWER BLADE DRIVE BELT

(See Fig. 25)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL-

Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION -

Install new belt in reverse order of removal.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower in reverse order of removal instructions.

IDLER

PULLEYS

MANDREL

PULLEY

ADJUSTMENTS

WITH PARKING BRAKE "ENGAGED"

DO NOT TOUCH THIS NUT. IF FURTHER

BRAKE ADJUSTMENT IS NECESSARY,

CONTACT YOUR NEAREST AUTHORIZED

SERVICE CENTEWDEPARTMENT

MANDREL

PULLEY

FIG. 25

TO ADJUST BRAKE (See Fig. 26)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted.

Depress clutch/brake pedal and engage parking brake.

Measure distance between brake operating arm and nut "A" on brake rod.

If distance is other than 1-3/4", loosen jam nut and turn nut "A" until distance becomes 1-3/4". Retighten jam nut against nut "A".

Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary. Contact your nearest au- thorized service center.

FIG. 26

TO ADJUST A'I-i'ACHMENT CLUTCH (See Fig. 27)

The electric clutch should provide years of service. The clutch has a built-in brake that stops the pulley within 5 seconds. Eventually, the internal brake will wear which may cause the mower blades to not engage, or, to not stop as required. Adjustments should be made by your nearest authorized service center/department.

Make sure attachment clutch and ignition switches are in "OFF" position.

Adjust the three nylon Iocknuts until space between clutch plate and rotor measures .012" at all three slot locations cut in the side of brake plate.

NOTE: After installing a new electric clutch, run tractor at full throttle and engage and disengage electric clutch 10 cycles to wear in clutch plate.

ROTORCLUTCH PLATE

.012"

BRAKE PLATE

NYLON LOCKNUT (3)

FIG. 27

23

Image 23
Contents Ill IIHiIIIIIIIIIII//IHIIIIIIII 111 Safe Operation Practices for Ride-On Mowers Safety RulesModel Maintenance AgreementLimited TWO Year Warranty on Craftsman Riding Equipment Limited 90 DAY Warranty on BatteryContents Performance Accessories and AttachmentsEngine Maintenance Parts packed separately in carton Parts Bag contents shown full sizeParts bag contents not shown full size Unpack Carton AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Connect Battery See FigAssemble Gauge Wheels to Mower Check Tire PressureCheck Deck Levelness Check Brake SystemTo Convert to Bagging or Discharging Install Mulcher PlateSee Figs Operation Speed Know Your TractorTo Move Forward and Backward HOW to USE Your TractorTo Adjust Mower Cutting Height To Transport See Figs Before Starting the EngineTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig ADD GasolineMulching Mowing Tips Mowing TipsDates Customer ResponsibilitiesGeneral Recommendations Before Each USEBlade Care BatteryTractor Brake OperationBelts EngineTransaxle Cooling Transaxle Pump FluidIN-LINE Fuel Filter See Fig To Service PRE-CLEANERTo Service Cartridge MufflerImportant if AN Attachment Other than Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigGround ServiceAdjustments To Level Mower HousingTo Replace Mower Blade Drive Belt To Adjust Brake See FigTo Adjust AI-iACHMENT Clutch See Fig Belt InstallationTo Replace Motion Drive Belt See Fig To Adjust Motion Control Lever See FigTransmission REMOVAL/REPLACEMENT To Remove CABLES, Reverse Order To Adjust Steering Wheel AlignmentTo Attach Jumper Cables Interlocks and Relays To Remove Hood and Grill Assembly See FigTo Replace Headlight Bulb Acceleration Test To Adjust Throttle Control Cable SeeTo Adjust Carburetor See Fig Final SettingCylinders Engine OILProblem Cause Correction Troubleshooting PointsEngaged Poor cut uneven PointsServicing of UNIT, They SchematicTractor -- Model Number Electrical Tractor --MODEL NumberUNC KEY Part NO. NO.DESCRIPTIONChassis and Enclosures KEY Part Description Tractor .. Model Number Repair PartsDrive Tractor - Model Number Steering AssemblyTractor --MODEL Number 1310 EngineTractor - Model Number 917,252714 Seat Assembly Description DecalsWheels & Tires 521 1617 18 Mower LiftRepair Parts Mower Deck 136420 Mulcher Cover 110485X Bearing Ball Mandrel 1135 Lower Kohler Engine Model Number MV18, Type Number PS58560 Repair Parts Crankcase Crankcase Tractor -- Model Number Crankshaft Service Notes Service Notes Service Notes LLI For Consumer Assistance HOT LINE, Call this Toll Free Number If YOU Need Repair Service Or PartsIll IIHiIIIIIIIIIII//IHIIIIIIII 111 Safety Rules Maintenance Agreement Contents Accessories and Attachments Hardware Pack Assembly Assembly Deck See Fig Checklist Operation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine ADD Gasoline Mowing Tips Customer Responsibilities Tractor Engine Cleaning Service and Adjustments Service See Fig Transmission REMOVAL/REPLACEMENT To Start Engine with a Weak Battery See Fig Service and Adjustments Sc. w Storage Troubleshooting Points Points UnD Repair Parts KEY Part NO. NO.DESCRIPTION Chassis and Enclosures Tractor -- Model Number Repair Parts Drive Tractor - Model Number Tractor --MODEL Number Optional Equipment Tractor - Model Number 917,252714 Seat Assembly Tractor -- Model Number Mower Lift Repair Parts Mower Deck KEY Part Description 1135 Lower Tractor -- Model Number Repair Parts Tractor --MODEL Number Crankcase Tractor -- Model Number Tractor --MODEL Number Service Notes Service Notes Service Notes LLI HP Twin Cylinder Electric Start