Sears 917.250551 manual Final Setting, Acceleration Test

Page 26

SERVICE AND ADJUSTMENTS

TO ADJUST CARBURETOR (See Fig. 33)

Tile carburetor has been present at the factory and adjust- ment should not be necessary However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load If the carburetor does need adjustment, proceed as follows:

In general, turning the adjusting needles in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mixture, Turning the adjusting needles out (coun- terclockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture

IMPORTANT: DAMAGE TO THE NEEDLES AND THE

SEATS IN CARBURETOR MAY RESULT IF SCREW IS TURNED IN TOO TIGHT

PRELIMINARY SETTING -

Be sure you have a clean air filter, and the throttle

control cable is adjusted properly (see "TO ADJUST THROTTLE CONTROL CABLE" in the Service and

Adjustments section of this manual)

With engine off turn idle fuel adjusting needle in (clock- wise) closing it finger tight and then turn out (counter- clockwise) 1 turn

FINAL SETTING -

Start engine and allow to warm for'five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position

The high idle is set at the factory and cannot be adjusted.

Idle speed setting - With throttle control lever in slow

(_) position, engine should idle at 1200 RPM If

engine idles too slow or fast, turn idle speed adjusting screw in or out until correct idle is attained.

Idle fuel needle setting - With throttle control lever in

slow (,,_.) position, turn idle fuel adjusting needle in (clockwise) until engine speed decreases and then

turn out (counterclockwise) approximately 3/4 turn to obtain the best low speed performance.

Recheck idle speed. Readjust if necessary

ACCELERATION TEST -

o Move throttle control lever from slow (_) to fast ("_) position. If engine hesitates or' dies, turn idle fuel

adjusting needle out (counterclockwise) 1/8 turn. Re- peat test and continue to adjust, if necessary, until engine accelerates smoothly

High speed stop is factory adjusted Do not adjust-damage may resulL

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED OVERSPEEDINGTHEENGINEABOVE

THE FACTORY HIGH SPEED SETTING CAN BE

DANGEROUS IFYOUTHINKTHEENGINE-GOVERNED

HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

NEAREST AUTHORIZED SERVICE CENTER/

DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND

EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Model Number 917.250551 Ownersmanual III. Children Safety is InvolvedII. Slope Operation ExhaustLimited 90 DAY Warranty on Battery Maintenance AgreementProduct Specifications Customer ResponsibilitiesContents Engine Maintenance PerformanceContents of Hardware Pack Unpack Carton Tools Required for AssemblyTo Remove Tractor from Carton Attach Steering WheelCheck Brake System Install Seat See FigCheck Tire Pressure Check Deck Levelness AssemblyInstall Mower and Drive Belt Check for Proper Position of ALL BeltsChecklist OPERATmON KnowyourtractorStopping HOW to USE Your TractorTo Adjust Mower Cutting Height Turn ignition keyTo Operate on Hills OperationBefore Starting the Engine To TransportADD Gasoline To Start Engine See FigBefore Each USE Lubrication ChartGeneral Recommendations REGOLARBYUCOSERV,CEMPLETBTires TractorBrake Operation BeltsLubrication To Clean Battery and TerminalsEngine Sparkplugs CleaningClean AIR INTAKE/COOLING Areas MufflerTo Level Mower Housing Serwce AN AdjustmentsTo Install TractorService Adjustments To Adjust Brake See Fig ServiceAdjustments To Adjust Attachment ClutchTo Replace Motion Drive Belt To Adjust Steering Wheel AlignmentFront Wheel TOE-IN Adjustment AS Viewed from BottomTo Replace Headlight Bulb Service and AdjustmentsTo Remove Wheel for Repairs To Replace FuseSee Fig To Adjust Afachment Lift SpringTo Remove Hood and Grill Assembly To Adjust Choke Control Servuce AdjustmentsTo Adjust Throttle Control Cable Final Setting Acceleration TestOther BatteryStorage Fuel SystemTroubleshooting Points Problem CauseTRO Bleshootrng POmNT$ CorrectionProperly Secure Your Wiring SchematicNON-REMOVABLE Removable Connections Wiring Insulated Clips Tractor - Model NumberKEY Part Description DecalsWheels & Tires KEY PartElectrical PT.O Tractor -- Model NumberElectrical PTOChassis and Enclosures 2117KEY Part NO. no UNCBepaib PARTSBAcTOBO0L Repahr Parts Ground DriveRepair Parts Steering AssemblyReparr Parts Is----s Tractor - Model Number EngineSeat Assembly KEY Part NO. no Lift AssemblyTractor Model Mower Deck REPAaR Parts KEY Part NO, noTransaxle 4197R Axle Shaft 8119M Needle Crankcase Kohler Engine Model Number CV22 PS67515Cylinder HEAD, Valve and Breather 151517 131211Cylinder HEAD/VALVE/BREATHER KEY Part Description Crankcase KEY Part NO. noAIR Intake Ignition / Electrical Blower Housing and Baffles255 AIR Intake KEY Part Tractor --MODEL NumberNot Illustrated NOo NOoDESCRIPTIONStarting System 23-17Engine Controls Starting System KEY Part Description OIL PAN/LUBRICATIONNOo 610 O36 CrankshaftFuel System Exhaust KEY Part Description Fuel System KEY PartCrankshaft KEY Part Description Not IllustratedService Notes Service Notes Rvice Notes LIJ = Model NUMBER-917.250551 If YOU Need Repair Service or PartsFor Repair SERVICE, Call this Toll Free Number Engine Model NO. 0V22S, Type NO. PS67515

917.250551 specifications

The Sears 917.250551 is a versatile and robust lawn mower that has garnered attention for its reliability and performance in maintaining residential lawns. With a blend of modern technology and user-friendly features, this mower is suitable for homeowners looking to keep their yards in pristine condition.

One of the notable attributes of the Sears 917.250551 is its powerful engine. Equipped with a reliable gas-powered engine, this mower delivers consistent performance, ensuring that even dense grass can be tackled effectively. The engine provides ample torque, which is especially beneficial for cutting through thick patches of grass without bogging down.

The mower features a self-propelling system that makes it easier for users to maneuver across various terrains. This technology allows the mower to adjust its speed based on the user's walking pace, providing a comfortable mowing experience while reducing fatigue. The adjustable speed settings cater to different user preferences and grass conditions, making it a flexible choice for diverse lawn care needs.

Another key feature of the Sears 917.250551 is its cutting deck size. The mower typically boasts a generous cutting width, allowing for faster mowing and fewer passes through your lawn. The cutting height is also adjustable, enabling users to customize the grass length according to their liking or seasonal requirements. This flexibility is crucial during different times of the year, as maintaining the optimal grass height can contribute to a healthier lawn.

In terms of build quality, the Sears 917.250551 is designed to withstand the rigors of outdoor use. Constructed with durable materials, it can handle various weather conditions and rough terrains. Maintenance is made straightforward with accessible parts, ensuring that users can perform routine checks and repairs with minimal hassle.

Furthermore, the mower is designed with safety features in mind. The blade brake system halts the blades' rotation immediately when the user releases the handle, minimizing the risk of accidents. Additionally, the ergonomic handles make it comfortable to operate, and they can often be adjusted for height to accommodate users of different statures.

Overall, the Sears 917.250551 stands out for its combination of power, ease of use, and user-friendly features. Whether you have a small yard or a more significant area to maintain, this mower is designed to deliver efficient and effective results, making it a dependable choice for lawn care enthusiasts.
Top Page Image Contents