Carburetor Adjustment, Seasonal Storage

Line exit holes					Line in Notch

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is re- leased.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Idle Speed

Screw

Air Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

WARNING: Perform the following steps after each use:

S Allow engine to cool, and secure the unit before storing or transporting.

SStore unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy storage. S Store in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio.

OTHER

SDo not store gasoline from one season to another.

S Replace your gasoline can if it starts to rust.

530163363 specifications

The Weed Eater 530163363 is a reliable and efficient tool designed for homeowners and landscaping professionals alike. Known for its performance and user-friendly design, this trimmer stands out in the competitive market of garden maintenance equipment.

One of the key features of the Weed Eater 530163363 is its powerful engine. It is equipped with a robust 25cc two-cycle engine that delivers significant power while remaining lightweight. This combination allows users to tackle tough weeds and overgrown grass with ease. The engine's design also promotes efficient fuel consumption, ensuring that users can maximize their working time without frequent refueling.

The 530163363 features a straight shaft design, which provides better reach and access to tight spaces such as under bushes or along fences. This feature is particularly beneficial for users needing to manage intricate landscaping or for those managing yards with various obstacles. The trimmer is fitted with a dual-line bump head, which allows for quick line advancement, making it easy to continue working without interruptions. This feature not only enhances the efficiency of trimming but also reduces downtime.

Another standout characteristic of the Weed Eater 530163363 is its ergonomic design. The lightweight construction minimizes user fatigue during extended use, while the adjustable handle allows for comfortable grip positioning. This flexibility ensures that even after long hours of use, users can maintain their comfort and control over the trimmer.

The inclusion of Easy Start technology also enhances the user experience. This feature reduces the effort required to start the engine, allowing for a hassle-free start-up even in challenging conditions. The engine is designed to offer a smooth operation, reducing vibrations that can cause discomfort during use.

In terms of maintenance, the Weed Eater 530163363 is designed for simplicity. Features like easy access to the air filter and spark plug make routine checks and maintenance straightforward, which is essential for prolonging the life of the trimmer.

In summary, the Weed Eater 530163363 combines power, efficiency, and user-centric design. Its impressive engine, ergonomic features, and maintenance-friendly design make it a valuable addition to any garden enthusiast's toolkit. Whether you are a homeowner or a professional landscaper, this trimmer offers the performance and reliability needed for effective lawn care.