Weed Eater 530088826 manual Carburetor Adjustments, Ignition Timing, Spark Plug

Page 5

SPush the line into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

SInsert the line into the the exit holes in the

hub as shown in the illustration.

SAlign the notches with the line exit holes. S Push spool into hub until it snaps into place. S Pull the lines extending outside of the hub to

release them from the notch.

We recommend all service and adjustments not listed in this manual be performed by an Authorized Service Dealer.

CARBURETOR ADJUSTMENTS

Your carburetor is equipped with limiter caps. Adjusting the carburetor is a complicated task. We recommend that you take your unit

to an Authorized Service Dealer. Damage will occur if you turn the needles beyond the limiter stops.

IGNITION TIMING

The ignition timing is fixed, non--adjustable.

SPARK PLUG

Replace the spark plug yearly using a Champion RCJ--8Y plug. Spark plug gap is 0.025 inches.

Need Assistance?

Call 1--800--554--6723.

Need Service Part?

Contact your dealer.

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing any of the recommended remedies below other than remedies that require operation of the unit.

TROUBLE

CAUSE

 

REMEDY

Engine will not

S

Engine flooded.

S

See “Starting.”

start.

S

Fuel tank empty.

S

Fill tank with correct fuel mixture.

 

S

Spark plug not firing.

S

Install new spark plug.

 

S

Fuel not reaching carburetor.

S

Check for dirty fuel filter; replace.

 

 

 

 

Check for kinked or split fuel line;

 

 

 

 

repair or replace.

 

S

Carburetor requires adjustment.

S

See “Carburetor Adjustments.”

Engine will not

S

Carburetor requires adjustment.

S

See “Carburetor Adjustments.”

idle properly.

S

Throttle trigger screw too

S

Loosen screw.

 

 

tight.

 

 

Engine will not

S

Air filter dirty.

S

Clean or replace air filter.

accelerate,

S

Spark plug fouled.

S

Clean or replace spark plug; re-gap.

lacks power,

S

Carburetor requires adjustment.

S

See “Carburetor Adjustments.”

or dies under

 

 

 

 

a load.

 

 

 

 

Engine

S

Fuel mixture incorrect.

S

Empty fuel tank and refill with

smokes

 

Air filter dirty.

 

correct fuel mixture.

excessively.

S

S

Clean or replace air filter.

 

S

Carburetor requires adjustment.

S

See “Carburetor Adjustments.”

Line does not

S

Line improperly routed in head.

S

Check line routing.

advance or

S

Line improperly wound on

S

Rewind line tightly and evenly.

breaks while

 

spool.

 

Use only 0.080” (2 mm) dia. line.

cutting.

S

Line size incorrect.

S

Line welds

S

Line size incorrect.

S

Use only 0.080” (2 mm) dia. line.

onto spool.

S

Incorrect spool.

S

Replace with correct spool.

 

S

Line is being crowded against

S

Cut with tip of line fully extended.

 

 

material being cut.

 

 

Line pulls

S

Too little line outside of head.

S

Remove spool and pull 4 inches

back into

 

 

 

(10 cm) of line outside of head.

head.

S

Line size incorrect.

S

Use only 0.080” (2 mm) dia. line.

 

 

 

 

 

5

Image 5
Contents URL Fuel Safety Operator SafetyUNIT/MAINTENANCE Safety Adjust the Handle Cutting SafetyTransporting and Storage Attach the ShieldHOW to Start Your Unit HOW to Stop Your UnitOperating Position Advancing the Cutting LineTroubleshooting Table Cause Remedy Carburetor AdjustmentsIgnition Timing Spark PlugElectrolux Home Products North America Your Warranty RightsDivision of WCI Products Inc., warrants to OriginalConsequential Damages Commencement Date The warrantyReplacement and Repair of Emission Related Parts Any

530088826 specifications

The Weed Eater 530088826 is a powerful and reliable string trimmer designed for homeowners and landscaping professionals alike. It has garnered attention for its robust performance, ease of use, and innovative features that make yard maintenance a breeze.

At the heart of the Weed Eater 530088826 is its potent engine, which delivers consistent power and efficiency. This model typically features a 25cc 2-stroke engine, providing ample power for tackling tough grass, weeds, and brush. The two-stroke design means that users will experience higher torque levels than a standard four-stroke engine, allowing for smoother operation and reduced vibrations during use. The result is a trimmer that can handle even the most challenging landscaping tasks without skipping a beat.

One of the standout features of the 530088826 is its bump feed mechanism. This intuitive system allows users to easily release more line with a simple bump of the trimmer head on the ground. Gone are the days of fumbling with manual line advancement; this convenience lets you keep your attention on the job at hand, ensuring that your trimming tasks are completed in a timely manner.

The Weed Eater 530088826 is also designed with user comfort in mind. Its lightweight and ergonomic construction minimizes user fatigue during long periods of use. The trimmer typically features a straight shaft design that provides efficient cutting reach into tight spaces and around obstacles like flower beds and fences. An adjustable handle allows for tailored grip positioning, granting better control and maneuverability throughout your trimming session.

Another impressive characteristic is its fuel efficiency. The 530088826 is engineered to provide maximum performance while consuming less fuel, making it an eco-friendly choice for environmentally conscious gardeners. Its design also includes a protective shield to minimize debris kickback, ensuring safety while working in various yard conditions.

In summary, the Weed Eater 530088826 is a reliable tool that merges power with user-friendly features. Its durable construction, efficient engine, bump feed technology, and ergonomic design make it an exceptional choice for anyone looking to maintain their lawn and garden areas effectively. Whether you are a seasoned professional or a weekend warrior, the Weed Eater 530088826 is equipped to handle the demands of yard work with ease and efficiency.