HOW to Stop Your Unit, Operating Position

HOW TO STOP YOUR UNIT

Push and hold the engine stop switch in the STOP or OFF position until the unit has fully stopped.

Choke lever

Trigger

Primer Bulb

Muffler

HOW TO START YOUR UNIT WARNING: The trimmer head will turn while starting the engine. A hot muffler can cause serious burns.

COLD ENGINE STARTING OR STARTING AFTER REFUELING

SSet unit on a flat surface.

SSlowly press the primer bulb 6 times.

SMove choke lever to FULL CHOKE posi-

tion.

S Squeeze the throttle trigger fully and hold through all remaining steps.

SPull starter rope handle sharply 6 times. S Move choke lever to HALF CHOKE posi-

tion.

S Pull starter rope handle no more than 6 pulls, until engine runs.

S Allow engine to run 10 seconds, then move choke lever to OFF CHOKE position.

RESTARTING A WARM ENGINE

SMove choke lever to OFF CHOKE position. S Pull starter rope handle until engine runs. S If engine does not start in 5 pulls, follow instructions in STARTING A COLD EN-

GINE.

OPERATING POSITION

ALWAYS WEAR:					Eye
ALWAYS WEAR:					Eye

Protection

Long Pants

Heavy Shoes

Cut from your right to your left.

ADVANCING THE CUTTING LINE

Advance line by tapping the bottom of the cut- ting head lightly on the ground while engine is running at full speed. The metal Line Limiter blade attached to the shield will cut the line to the proper length.

REPLACING THE LINE

SPush and hold the engine stop switch in the stop/off position until the unit has fully stopped.

SDisconnect the spark plug lead wire.

SRemove spool by firmly pulling on tap but-

ton.

SClean entire surface of hub and spool.

SReplace with a pre-wound spool, or cut two lengths of 12-1/2feet of .080” (2 mm) diam- eter Weed Eaterr brand line. Never use wire, rope, string, etc., which can break off

and become a dangerous missile.

SInsert ends of the line about 1/2 inch (1 cm) into the small hole on the inside of spool.

Spool

Small

Holes

Line exit holes					Line in Notch

Line in Notch

Hub

S Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

SPush the line into the notches, leaving 3 to 5

inches (7 -- 12 cm) unwound.

SInsert the line into the the exit holes in the hub as shown in the illustration.

SAlign the notches with the line exit hole.

SPush spool into hub until it snaps into place. S Pull the line extending outside of the hub to

release it from the notch.

We recommend all service and adjustments not listed in this manual be performed by an Authorized Service Dealer.

CARBURETOR ADJUSTMENTS

Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an Authorized Service Dealer. Damage will oc- cur if you turn the needles beyond the limiter stops.

IGNITION TIMING

The ignition timing is fixed, non-adjustable.

SPARK PLUG

Replace the spark plug yearly using a Cham- pion RCJ--8Y plug. Spark plug gap is 0.025”.

530087729 specifications

The Weed Eater 530087729 is a well-regarded trimmer known for its efficiency and reliability, tailored specifically for homeowners and landscaping enthusiasts looking to maintain a well-groomed yard. This model stands out due to its powerful performance and user-friendly design, making yard maintenance a less daunting task.

One of the primary features of the Weed Eater 530087729 is its lightweight construction, which allows for easy maneuverability. Weighing around 9.5 pounds, this trimmer enables users to work for extended periods without experiencing significant fatigue. The ergonomic handle design further enhances comfort, allowing for better grip and control during various trimming activities.

The 530087729 is equipped with a robust 2-cycle engine, which delivers a reliable and powerful performance, ensuring effective cutting through dense grass and stubborn weeds. This engine technology is praised for its ability to start quickly with minimal effort, often featuring an advanced primer bulb and choke system to facilitate smooth ignition.

One of the highlight features of this trimmer is its bump-feed line advancement system. This mechanism allows users to easily release more cutting line with a simple tap on the ground, ensuring continuous operation without the need to stop and manually adjust the trimmer. This feature significantly enhances productivity by minimizing downtime during trimming tasks.

Durability is another key characteristic of the Weed Eater 530087729. Constructed with high-quality materials, this trimmer is designed to withstand the rigors of regular use. The reinforced shaft helps to reduce vibrations, leading to improved comfort while operating the machine.

Additionally, the trimmer boasts multiple attachments compatibility, making it a versatile tool for various yard maintenance tasks. Users can easily swap heads for different functions, such as edging, cultivating, and more, transforming the 530087729 into a multi-functional gardening tool.

Overall, the Weed Eater 530087729 combines power, comfort, and versatility, making it an ideal choice for anyone aiming to achieve a pristine outdoor space. Its lightweight design, efficient engine, bump-feed system, and attachment capabilities position it as a reliable investment for long-term yard care. Whether tackling tough weeds or maintaining the edges of a garden, this trimmer proves to be an invaluable ally in creating a beautiful landscape.