Cub Cadet ST26, ST23, ST35 manual Carburetor Adjustment, Emission Parts Maintenance Chart

Page 19

MAINTENANCE

 

 

EMISSION PARTS MAINTENANCE CHART

 

 

 

 

 

 

 

 

 

 

 

 

PART

MAINTENANCE

BEFORE

MONTHLY or

THREE MONTHS or

SIX MONTHS or

YEARLY or

 

SEE

 

 

 

USE

50 HOURS USE

150 HOURS USE

300 HOURS USE

600 HOURS USE

 

PAGE

 

 

 

 

 

 

 

 

 

Air Filter

Clean

X

 

 

 

 

 

21

 

 

 

 

 

 

 

 

 

Element

Replace

 

 

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spark Plug

Check / Clean / Adjust

 

X

 

 

 

 

20

 

 

 

 

 

 

 

 

 

 

 

Replace

 

 

 

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Carburetor

Clean (*1)

 

 

X

 

 

 

18,19

 

 

 

 

 

 

 

 

 

 

 

Overhaul (*2) / Replace (*3)

 

 

 

 

X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(*1)

• At an authorized Cub Cadet Commercial servicing facility to be charged.

 

 

 

(*2)

• For consumer use / At an authorized Cub Cadet Commercial servicing facility to be charged.

 

(*3)

• For commercial use / At an authorized Cub Cadet Commercial servicing facility to be charged.

NOTE:

Time intervals shown are a maximum. Actual use and your experience will determine the frequency of required maintenance.

You should be charged for the cost of any required replacement except warranty replacement under LIMITED WARRANTY and/or EMISSION CONTROL WARRANTY.

A. CARBURETOR ADJUSTMENT.

The carburetor is preset at the factory. This is the optimum setting under the barometric pressure and climatic conditions at the factory and is suitable for most operating sites.

It ensures that your machine will run smoothly, be fuel efficient, operate reliably and produce low emissions.

If the engine runs unsatisfactorily at high altitudes or at sea level, slight readjustment of the carburetor may be necessary:

NOTE

Every unit is run at the factory and the carburetor is set in compliance with EPA. In addition, the carburetor is equipped with H and L needle adjustment limiters that prevent settings outside acceptable limits.

1.Check the air filter and clean it if necessary.

2.Check the spark arresting screen (if fitted) and clean it if necessary.

H L

I

3.Mount the cutting tool.

a.Nylon line trimmer head:

Trim lines to the correct length. (The lines must extend as far as the line limiting blade on the deflector.

4.Start the engine and adjust the idling speed correctly with the idle speed adjusting screw (Ref. I). The cutting tool must not rotate.

5.Warm up the engine.

18

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Trimmers Foreword Table of ContentsGeneral Safety PrecautionsProtecting Others Carbon Monoxide Hazards Preparation for the USE of the TrimmerOperation Safety Precautions Metal Blade USE Shaft Decals Decal InformationSpecifications REF no Description Parts DescriptionMounting the Cutting Tool Trimmer AssemblyMounting the Loop Handle Mounting the DeflectorUsing the Shoulder Harness Standard on ST35 Fueling Instructions Directions for Mixing See Chart for AmountsMixing Instructions Fuel MixtureOperation When the Engine is ColdStarting If the Engine Doesnt Start When the Engine is WarmStopping Yearly See USE MaintenanceEmission Parts Maintenance Chart Carburetor AdjustmentProper idling speed Adjusting the idle speedCutting tool rotates when the engine is idling Adjusting high speedChecking the Spark Plug Throttle Wire AdjustmentCooling System MAlNTENANCE Cleaning the AIR FilterCleaning the Exhaust Port Cleaning the Cylinder FinsCleaning the Clutch and Clutch Drum Lubricating the Gear Head Fuel SystemLubricating the Drive Shaft Problem Cause Solution Troubleshooting GuideHOW to Order Parts Your Warranty Rights and Obligations EPA Emission Control Warranty StatementEmission Control Warranty Parts List Parts List ENGINE, ST23 Trimmer ENGINE, ST23 Trimmer Ð Parts List SHAFT, ST23 Trimmer Optional SHAFT, ST23 Trimmer Parts ListENGINE, ST26 Trimmer ENGINE, ST26 Trimmer Parts List SHAFT, ST26 Trimmer SHAFT, ST26 Trimmer Parts List ENGINE, ST35 Trimmer ENGINE, ST35 Trimmer Parts List SHAFT, ST35 Trimmer SHAFT, ST35 Trimmer Parts List

ST35, ST23, ST26 specifications

The Cub Cadet ST26, ST23, and ST35 snow blowers are excellent machines designed for efficient snow removal. Built with durability in mind, these models come equipped with robust features and advanced technologies aimed at enhancing performance and ease of use during winter months.

One of the main features of the Cub Cadet ST series is its powerful engines. The ST26 is powered by a 243cc engine, while the ST23 has a slightly smaller engine but still delivers commendable power for residential use. The ST35, on the other hand, boasts a more robust engine that provides superior snow removal capability, ideal for larger driveways or more substantial snowfall. The engines ensure reliable starts, even in cold temperatures, which is essential during winter.

These snow blowers also feature an innovative electric start option, allowing users to start the machine with just the push of a button. This convenience is particularly beneficial on frigid mornings when a traditional pull-start may be less appealing.

Another highlight of the ST series is the Cub Cadet's patented Intuitive Control System. This system allows users to easily adjust the speed, direction, and chute angles with minimal effort. With multiple forward and reverse speeds, users can navigate through varying snow conditions and terrain seamlessly.

The composite poly chute is another great feature, designed to provide enhanced throwing distance and prevent clogging. This innovative chute design helps direct snow exactly where users want it, saving time and effort when clearing driveways and walkways.

Additionally, the ST series snow blowers come with oversized tires that offer enhanced traction, allowing for better stability and maneuverability on slippery surfaces. The machines are also equipped with heated hand grips, ensuring comfort in extremely cold conditions.

Built with a strong, durable frame, these snow blowers are constructed to withstand the rigors of winter use. The reinforced housing provides additional protection against wear and tear, making the ST series reliable over years of heavy use.

In summary, the Cub Cadet ST26, ST23, and ST35 snow blowers present an array of advanced features and technologies. With powerful engines, intuitive controls, and robust construction, they stand out as efficient solutions for snow removal. Whether tackling light snowfalls or heavy winter storms, these machines offer performance and reliability, making them an excellent choice for homeowners seeking to conquer winter weather challenges.
Top Page Image Contents