Weed Eater 530088774 manual Carton Contents, Assembly Tools Required, Configuring Your Unit

Page 4

homeowner use, the muffler and spark arrest- ing screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your Au- thorized Service Dealer.

Handlebar Screw

Bracket Cover

Mounting

Bracket

CARTON CONTENTS

Check carton contents for the following:

Sbrushcutter

Shandlebar screws (2)

Sblade shield screws (4) S cupped washer

S large nut for installing blade S long hex wrench

S short hex wrench S bracket cover

S metal shield S plastic shield

S shoulder strap with warning S weed blade

S trimmer head (assembled on unit) S handlebar

S container of oil

Examine parts for damage. Do not use dam- aged parts.

NOTE: If you need assistance or find parts missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the empty fuel tank.

Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.

ASSEMBLY

WARNING: Always stop unit and dis- connect spark plug before performing any as- sembly procedures.

WARNING: Make sure your unit is properly assembled and all fasteners are se- cure.

TOOLS REQUIRED

S2 Hex wrenches (provided)

SAdjustable wrench or large pliers S Phillips screwdriver

ATTACHING THE HANDLEBAR

ASSEMBLY OF SHOULDER STRAP

WARNING: Proper shoulder strap and handlebar adjustments before starting the engine are required.

STry on shoulder strap and adjust for fit and balance before starting the engine or begin- ning a cutting operation.

SInsert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist.

NOTE: A one-half twist is built in the shoul- der strap to allow the strap to rest flat on the shoulder.

S Adjust the strap, allowing the hook to be about 6 inches below the waist.

SFasten the strap hook to the clamp located between the trigger handle and the handle- bar clamp base and lift the tool to the oper- ating position.

CONFIGURING YOUR UNIT

You can configure your unit using a cutting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1/2 inch in diameter. To assemble your unit, go to the section for the desired configuration and follow the instructions.

ASSEMBLY INFORMATION - TRIMMER HEAD

TRIMMER

HEAD

DANGER: During blade usage, the barrier portion of the handlebar must be installed as shown to provide a barrier be- tween operator and the spinning blade.

SLocate the decal on the handlebar. This de- cal includes two arrows. Position the han- dlebar with the mounting bracket between these arrows.

SPosition the bracket cover over the handle- bar. Again make sure the handlebar is be- tween the arrows.

S Insert screws and hand tighten only. Be sure the handlebar is installed correctly; then, tighten each screw securely with the short hex wrench.

4

NOTE: Remove the blade and metal shield before attaching the plastic shield and trim- mer head. To remove blade, push in locking lever and hold. Rotate blade nut until the lock- ing lever falls into one of the grooves in the dust cup. Continue to hold the locking lever. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clockwise. Release locking lever. Remove both washers and blade. To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLING THE METAL BLADE for illustrations. Be sure to store all parts and instructions for future use.

Image 4
Contents URL Operator Safety Eye Thrown Protection Objects Leg Guards Boots Hazard ZoneAlways Wear Stop coasting blade by contact with cut materialUNIT/MAINTENANCE Safety Fuel SafetyCutting Safety Transporting and StorageCarton Contents Assembly Tools RequiredAttaching the Handlebar Assembly of Shoulder Strap Configuring Your UnitAssembly Information Weed Blade Attaching the Plastic Shield and Trimmer HeadAttaching the Metal Shield Weed BladeInstallation of the Metal Blade HOW to Stop Your UnitHOW to Start Your Unit Dust Cup Blade Retaining WasherStarting a Warm Engine Operating PositionOperating Instructions for USE with Trimmer Head Advancing the Trimmer LineReplacing the Line Carburetor Adjustment Need Service PART?Troubleshooting Table Cause Remedy Spark PlugPOULAN/WEED Eater at 1--800--554--6723. Warranty COM Quential Damages POULAN/WEED