McCulloch 248530 Handle Assembly, Carburettor Adjustment, Starting and Stopping the Engine

Page 11

G.ENGINE/SHAFTASSEMBLY

A

DANGER. Do not run engine without shaft attached as clutch could fly off.

1) Insert the shaft (A) into the engine joint (B) making the female squared end (C) inside the joint mates with the male squared end (D) of the shaft.

Rotate the shaft from right to left to obtain a precise fit. Now tighten the locking bolt (E) clockwise to ensure the shaft is held firmly in the joint.

2)If the joint is not tightened onto the engine housing, first make sure the shaft is fully and correctly engaged up to the shank, then tighten the 4 screws (A) in a criss-cross sequence.

3) Assemble the eyelet (A) of the ground wire onto the end of the throttle cable and install the washer (B).

Insert the throttle cable into the cable mount

(C), install the second washer (B) and insert the hexagonal nut.

4)Fit the end of the trigger cable connector (B) into the slot on swivel (C).

5)Adjust the nut (D) of the trigger cable connector so that the cable can easily slide in the opening with a play of 1 mm before operating the swivel (C).

Tighten now the hexagonal nut (E).

6)Stop switch (STOP) cable: fit the connection.

H.HANDLEASSEMBLY

J FRONT HANDLE

Secure the handle in front of the label placed on the shaft 11 cm from the rear grip when assembling nylon string head and 36 cm when

assembling metallic blades. This position ensures optimum balance and safety. The handle must be perpendicular to the shaft as illustrated.

I.STARTINGANDSTOPPINGTHEENGINE

WARNING. First read sections: SAFETY RULES, SAFETY USAGE and SYMBOLS.

COLD ENGINE STARTING

1)Move stop switch to the “ON” position.

2)Depress the safety lever (S), squeeze the accelerator trigger (A) and push the throttle advance forwards (B). Now release the accelerator trigger (A) and then the throttle advance (B).

WARNING: when the throttle advance is engaged, the head or blade rotates.

3)Move choke lever (E) to the closed position .

4)Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope until engine fires once.

5)Move choke lever (E) to the open position then pull starter rope until engine fires. Let engine run for a few seconds holding the trimmer. Now disengage throttle advance by pulling trigger completely. Engine will now keep on running at idle speed.

HOT ENGINE STARTING

STOP switch on START position I. Trigger on idle position (released).

Choke towards (open position ). Press the primer bulb (C) several times until you see fuel going back to carburetor through pipe (D). Pull starter rope.

WARNING: when the throttle (B) advance is engaged, the head or blade rotates.

6)ENGINE STOPPING

Press the stop switch moving it to STOP position 0.

WARNING: when the engine is switched off rotating parts, blade or nylon string head, will keep on rotating for a few seconds. Hold the machine until all parts come to a standstill.

N.B. In an emergency the above mentioned delay in stopping may be shortened by touching blade parallel on the ground.

L.CARBURETTORADJUSTMENT

Your machine may be fitted with a highly sensitive low emission carburettor. We now therefore recommend that carburettor adjustments are only made by an authorised servicing dealer, equipped with instruments that will ensure best performance with lowest emission levels.

To adjust the idle speed, however, proceed as follows:

With engine running and warm, slowly turn screw ‘I’ or ‘T’ clockwise until the engine runs smoothly with a consistent noise level but without making the chain or cutting head rotate.

If the cutting attachment does move or the engine

9

Image 11
Contents Cabrio 246/25 cc 25cc Caracteristiques Techniques Technical DataTekniska Data Datos TecnicosTekniske Data Tekniset TiedotTilos tankolás közben Page General Description Safety RulesBlades and Nylon String Head Assembly Blade Safety UsageFuel MIX Safety Guard AssemblyBlade and Nylon String Head Assembly Starting and Stopping the Engine Handle AssemblyCarburettor Adjustment Fuel Filter Regular MaintenanceFault Finding Table AIR Filter Cleaning

248530, 95390024200 specifications

The McCulloch 95390024200, 248530 is a powerful and versatile chainsaw designed for both amateur and experienced users. Known for its reliability and cutting efficiency, this chainsaw is perfect for a variety of tasks, including pruning trees, cutting firewood, and tackling more demanding landscaping projects.

One of the key features of the McCulloch 248530 is its robust engine. The chainsaw is equipped with a 40cc two-stroke engine that delivers impressive power while maintaining a lightweight design. This combination allows users to handle extended cutting tasks without experiencing excessive fatigue. The engine's design not only enhances performance but also ensures lower emissions, making it an environmentally friendly choice.

Another notable technology incorporated into the McCulloch 95390024200 is the Easy Start system. This innovation significantly reduces the amount of effort needed to start the chainsaw, allowing users to get to work quickly and efficiently. The Easy Start mechanism minimizes the resistance when pulling the starter cord, making it accessible for people of all skill levels.

The chainsaw features a tool-less chain tensioning system, which simplifies the process of adjusting the chain tension. This is particularly useful for users who need to make quick adjustments in the field. The access point for tensioning is conveniently located, which means that users spend less time on maintenance and more time cutting.

The McCulloch 248530 also boasts a 16-inch guide bar, providing excellent cutting capacity for various applications. The Oregon saw chain ensures smooth and efficient cutting, allowing users to make precise cuts with minimal effort. Additionally, the chainsaw comes with an automated oiling system that continuously lubricates the chain during operation, extending the lifespan of both the chain and the bar.

Safety features have not been overlooked in the McCulloch 95390024200. It incorporates a chain brake that activates instantly in case of kickback, significantly reducing the risk of injury. The ergonomic design of the handle ensures a comfortable grip, reducing vibrations and allowing for better control during prolonged use.

In summary, the McCulloch 95390024200, 248530 is not just another chainsaw; it is a blend of power, technology, and safety, making it an excellent choice for various cutting tasks. With its easy-start engine, tool-less chain tensioning, and robust safety features, this chainsaw promises to meet the demands of both casual users and professionals alike.