Troy-Bilt 13A-344-563 manual Servicing Your Rider Mower, Belt Replacement, Deck Belt

Page 16

Loosen hex nuts

to adjust

Do not adjust hex nut

Deck

Height

Lever

Ferrule

 

Helper

 

Spring

Remove Hairpin Clips

 

and Washers

Lower

 

Link

Hanger

Link

Figure 14

Front to Rear Levelling

Place the deck in the highest position.

Wearing a pair of heavy work gloves to prevent injury, rotate the cutting blade so that it is pointed front to back and parallel to the rider. Depress and lock the deck engagement pedal.

Completely loosen, but do not remove, the top hex nut out of the three hex nuts that hold the hex bolt and the ferrule on the deck hanger link assembly. See Figure 14 .

IMPORTANT: Do not try to loosen/ tighten bottom nut.

Thread the middle nut as far down as possible.

Keeping an equal number of threads above each of the nuts, thread the upper nut down until the front tip of the blade is 1/4” to 3/8” lower than the rear tip of the blade. Note that threading this nut down will raise the front of the deck.

Thread the middle nut up against the base of the ferrule. See Figure 14 .

Tighten the upper nut against the top of the ferrule to lock adjustment.

Side to Side Levelling

Place the deck in the highest position.

Wearing heavy work gloves to prevent injury, rotate the cutting blade so that it is pointed side to side and perpendicular to the rider. Depress and lock the deck engagement pedal.

Loosen the middle hex nut.

Thread the top hex nut up or down in order to set both tips of the blade at an equal height from the ground. Remember to thread the nut down to raise the deck, and thread up to lower the deck.

Once the deck is level, thread the middle hex nut to tighten against the ferrule. Make sure the cut is even and the lift lever moves to all cutting heights.

SECTION 7: SERVICING YOUR RIDER MOWER

Belt Replacement

There are two drive belts and one deck belt in your rider mower; follow the description below to identify the belts.

1.The lower drive belt goes from the variable speed pulley to the transmission pulley.

2.The upper drive belt goes from the variable speed pulley to the upper sheave of engine pulley.

3.The deck belt goes from the deck pulley to the lower sheave in engine pulley.

Periodically check to see if these belts are too loose or damaged through wear and tear. If so, replace with new belt.

Deck Belt

Engage the parking brake and turn the ignition off. Pivot the seat frame up and remove the grasscatcher. Remove the spark plug wire.

Put the deck at the lowest cutting height by adjusting the cutting height adjustment lever to the lowest position.

Using a 9/16” wrench, loosen the hex nut on the idler pulley. See Figure 15.

Using a 1/2” socket wr ench, remove two self- tapping screws, lock washer and hex nut that hold the deck belt cover to the deck. See Figure 15 . For this, you will have to work from the top left side of the mower. Remove the cover.

16

Image 16
Contents Operator’s Manual Table of Contents Three 3 Year Limited Warranty General Operation Important Safe Operation PracticesSlope Operation Do Not ServiceChildren Page Slope Guage Attaching Battery Cables Unpacking & Assembling Your Rider MowerLoose Parts Attaching Side-Discharge ChuteAttaching Hitch Plate Optional Attaching Mulch PlugAttaching Bumper Optional Know Your Rider Mower Safety Interlock Using Shift LeverGrass Fill Level Indicator Stopping MowerOperating Your Rider Mower Stopping Mower Using The Mower To Empty Grass CatcherMulching To empty grass bag, stop the mower completelyBrake Adjustment Cutting HeightSeat Position Blade Brake/PTOAdjusting the Deck Wheel AlignmentBelt Replacement Servicing Your Rider MowerDeck Belt Front to Rear LevellingFuse Replacement Lower Variable Speed BeltKeeper Upper Variable Speed BeltMaintaining Your Rider Mower General RecommendationsCutting Blade Oil Drain SleeveEngine Cleaning EngineLubrication TROUBLE-SHOOTING BatteryRider Mower EngineBelt shreds Belt guides or guards incorrectly adjusted

13A-344-563 specifications

The Troy-Bilt 13A-344-563 is a robust and reliable tiller that caters to both gardening enthusiasts and professional landscapers alike. Known for its durability and efficiency, this tiller is designed to make the often labor-intensive process of soil cultivation easier and more effective.

One of the standout features of the Troy-Bilt 13A-344-563 is its powerful engine. Equipped with a reliable 3.5 HP engine, this tiller is capable of tackling tough soil conditions with ease. The engine's performance ensures that gardeners can break up hard, compacted soil efficiently, allowing for better plant growth and a healthier garden.

The tiller is also designed with a large tilling width of up to 16 inches, enabling users to cover more ground in less time. This feature is particularly advantageous for those with larger gardens or landscaping projects. Alongside its width, the tiller has a tilling depth of up to 8 inches, making it suitable for a variety of soil types and gardening tasks.

The Troy-Bilt 13A-344-563 incorporates patented technologies that enhance its ease of use. One such feature is the adjustable tilling depth, which allows users to customize how deep they want to till based on the specific needs of their garden. Additionally, its rear-tine design helps to maintain stability and provides a smoother operation when maneuvering around different garden terrains.

Furthermore, the tiller boasts a user-friendly design with an ergonomic handle that reduces fatigue during prolonged use. The handles are adjustable, allowing users of various heights to find a comfortable position while operating the machine. This thoughtful design is geared towards maximizing efficiency without sacrificing user comfort.

Maintenance is also a breeze with the Troy-Bilt 13A-344-563. Its easy-access oil fill and dipstick make routine checks and changes hassle-free. Additionally, the robust construction ensures that the machine can withstand regular use over an extended lifespan.

In summary, the Troy-Bilt 13A-344-563 combines powerful performance, versatile features, and user-friendly design, making it a valuable addition to any gardener’s toolkit. Whether preparing soil for planting or cultivating existing beds, this tiller stands out for its ability to deliver reliable, effective results that promote healthy, vibrant gardens.