Troy-Bilt 494 manual Shredder Blade, Storing Your Chipper Shredder

Page 11

make sure to remove an equal amount from each blade and torque to 250 - 300 in. lbs.

NOTE: Make certain blades are reassembled with the sharp edge facing upward.

Shredder Blade

•Disconnect the spark plug wire and ground against the engine.

•Lower the hopper assembly and block up the housing.

•Remove the six hex lock nuts and flat washers from the weld studs on the flail housing.

•Separate the hopper assembly from the impeller assembly and remove the support plate.

NOTE: When reassembling the support plate, the embossed tab must face inward towards the impeller.

•Remove the two wing knobs and cupped washers that secure the discharge chute and raise the chute.

•Insert a 1/2” or 3/4” diameter pipe through the flail screen into the impeller to keep it from turning or remove the flail screen and insert a piece of wood into the chute opening.

•Remove the two outside screws on the blade, using a 3/16” allen wrench and a 1/2” wrench.

See Figure 10.

•Remove the blade by removing the center bolt, lock washer, and flat washer.

NOTE: Use caution when removing the blade to avoid contacting the weld studs on the housing.

•When sharpening the blade, follow the original angle of grind as a guide. It is extremely important

that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade.

Discharge Chute

Blade

Weld Stud

 

Flat Screw

 

Hex Bolt

 

Figure 10

•An unbalanced blade will cause excessive vibration when rotating at high speeds and may cause damage to the unit. The blade can be tested by balancing it on a screwdriver or nail. Remove metal from the heavy side until it is balanced evenly.

•When reassembling the blade, tighten center bolt to between 550 and 700 in.-lbs. and the two out bolts to between 250 and 350 in.-lbs.

Storing Your Chipper Shredder

•Clean the equipment thoroughly.

•Wipe equipment with an oiled rag to prevent rust.

•Refer to engine manual for correct engine storage instructions

•Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents OPERATOR’S Manual Table of Contents Preparation Important Safe Operation PracticesTraining Operation Maintenance And StorageRemoving Unit From Carton Disconnecting Spark Plug WireAssembling Your Chipper Shredder Your ResponsibilityAttaching the Discharge Chute Attaching the Hopper AssemblyAttaching the Bag Know Your Chipper ShredderAttaching the Chipper Chute Starting Engine Operating Your Chipper ShredderStopping Engine Gas and Oil Fill-UpCustomer Responsibilities Lowering the Hopper AssemblyUsing the Chipper Shredder To Empty BagChipper Blades MaintenanceLubrication Removing the Flail ScreenStoring Your Chipper Shredder Shredder BladeProblem Cause Remedy TroubleshootingPage Parts List for Model Part Description ModelMANUFACTURER’S Limited Warranty for
Related manuals
Manual 13 pages 28.76 Kb

494 specifications

The Troy-Bilt 494 is a powerful and versatile garden tiller designed to make soil preparation an efficient and straightforward task. With its sturdy construction and innovative features, it is a favored choice among both gardening enthusiasts and professional landscapers.

At the heart of the Troy-Bilt 494 is its robust engine that delivers reliable power and performance. The tiller is equipped with a powerful four-cycle engine that ensures consistent torque and efficiency. This engine provides ample power to break up tough soil, allowing users to tackle any gardening project with ease.

One of the standout features of the Troy-Bilt 494 is its counter-rotating tines. This technology allows the tines to rotate in the opposite direction of the tiller, effectively cutting through hard soil and mixing in organic matter like compost and mulch. The counter-rotating action helps to aerate the soil better, promoting healthier root growth and improving overall soil quality.

The tiller's adjustable tilling width is another significant characteristic. Users have the flexibility to choose between different widths, allowing for versatile use in various garden sizes and layouts. This feature makes it easy to navigate around plants and other obstacles, ensuring that every inch of the garden can be cultivated effectively.

User comfort is also a priority with the Troy-Bilt 494. The tiller comes with soft-grip handles that reduce fatigue during extended use, making it comfortable for gardeners of all experience levels. Additionally, its lightweight design enhances maneuverability, ensuring that users can navigate tight spaces easily.

The durability of the Troy-Bilt 494 cannot be understated. Built with high-quality materials, it can withstand the rigors of frequent use and demanding gardening tasks. Its heavy-duty frame is designed to handle tough working conditions while providing stability and control during operation.

In terms of maintenance, the Troy-Bilt 494 is designed for ease of use. With accessible components, regular maintenance tasks such as oil changes and spark plug replacements can be performed without hassle. This commitment to user-friendly design ensures that gardeners spend more time tilling and less time on upkeep.

Whether you're preparing a new garden bed, mixing in compost, or cultivating between rows, the Troy-Bilt 494 tiller combines power, efficiency, and user-friendly features, making it an essential tool for anyone serious about gardening.
Top Page Image Contents