Operation (continued)
Resetting Your Inverter/Charger to Restore AC Power
Your Inverter/Charger may cease supplying AC power or DC charging power in order to protect itself from overload or to protect your electrical system. To restore normal functioning:
Overload Reset: Switch operating mode switch to “DC OFF” and remove some of the connected electrical load (i.e., turn off some of the AC devices drawing power which may have caused the overload of the unit). Wait one minute, then switch operating mode switch back to either “AUTO/REMOTE” or “CHARGE ONLY.”
Output Circuit Breaker Reset: If tripped, remove a portion of the load, wait one minute and then press breaker button to reset.
Configuration
Set Configuration DIP Switches
Using a small tool, set the Configuration DIP Switches (located on the front panel, see diagram) to optimize Inverter/Charger operation depending on your application. Refer to the appropriate section to review the instructions for your specific model.
B4 | B3 | B2 | B1 | A4 | A3 | A2 | A1 |
INPUT C/B |
Group B Dip Switches | Group A Dip Switches |
|
Group A DIP Switches (All Models)
Using a small tool, configure your Inverter/Charger by setting the four Group A DIP Switches (located on the front panel of your unit; see diagram) as follows:
| A1 | Select Battery |
|
|
|
|
|
|
|
|
|
|
| |
|
| A4 |
| A3 |
| A2 |
| A1 |
|
|
| |||
| CAUTION: The Battery Type DIP Switch setting must match |
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||
| the type of batteries you connect, or your batteries may be |
|
|
|
|
|
|
|
|
|
|
| ||
| degraded or damaged over an extended period of time. See |
|
|
|
|
|
|
|
|
|
|
| ||
| "Battery Selection" section for more information. |
|
|
|
|
|
|
|
|
|
|
|
| |
| Battery Type |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| Switch Position |
|
|
|
|
|
|
|
|
|
|
|
| |
| AGM/Gel Cell (Sealed) Battery | Up |
|
|
|
|
|
|
|
|
|
| ||
A2 Select Charger Enable/Inhibit Switch is preset to ENABLE, which permits continuous battery charging. If you are connecting your unit to batteries with a separate charger, you may set this switch to INHIBIT to disable its
A4 |
| A3 |
| A2 |
| A1 | INHIBIT |
ENABLE
Wet Cell (Vented) Battery | Down (factory setting) |
Battery Type | Switch Position |
Inhibit | Up |
Enable | Down (factory setting) |
A4 A3 Select Low AC Input Voltage Point for Switching to
Voltage and Level
120V Models | 230V Models | Switch Position |
|
|
|
A 105V | 201V | A4 Up & A3 Up |
|
|
|
B 95V | 182V | A4 Up & A3 Down |
|
|
|
C 85V | 163V | A4 Down & A3 Up |
|
|
|
D 75V | 144V | A4 Down & A3 Down |
|
| (factory setting) |
|
|
|
*Most of your connected appliances and equipment will perform adequately when your Inverter/Charger's Low AC Voltage Input Point (DIP Switch #3 and #4 of Group A) are set to Level B (95V for 120V Models/182V for 230V Models). However, if the unit frequently switches to battery power due to momentary low line voltage swings that would have little effect on equipment operation, you may wish to adjust this setting. By decreasing the Low AC Voltage Input Point, you will reduce the number of times that your unit switches to battery due to voltage swings.
A4 A3 A2 A1
Level A
A4 A3 A2 A1
Level B
A4 A3 A2 A1
Level C
A4 A3 A2 A1
Level D
5