VTech 6778, 6767, 6779, 6787, 6789, I6757 quick start Quick start guide

Quick start guide

for models i6757/6767/6778/6779/6787/6789

STEP 1 Connect power to telephone base and chargers then connect telephone line to telephone base

• Plug the connector into the power jack at the bottom

of the telephone base and chargers then plug the

power adapter into an electrical outlet not controlled

by a wall switch.

STEP 3 Make, receive, and end calls

STEP 4 Set the answering system clock

• Press CLOCK to listen to the current clock setting.

• Press CLOCK again to change the settings.

• Press /SKIP or /REPEAT to change the year, hour, minute, or date.

When the correct setting is announced, press CLOCK to advance to the next setting.

NOTE:

For complete feature instructions, please refer to your user’s manual.

• Plug one end of the telephone line cord into the

telephone line jack at the bottom of the telephone

base. Then plug the other end of the cord into the

modular wall telephone outlet.

NOTE: Use only the power adapters supplied with your VTech telephone or equivalent.

STEP 2 Install the battery

•Align the two holes in the plug with the socket pins matching the color-coded label in the battery compartment of the handset, then snap the plug securely into place.

•Place the battery in the compartment with the wires in the upper right corner.

•Position the battery compartment cover and slide it towards the unit until it clicks into place.

•For optimal performance, we recommend that you charge the handset for 16 hours. Note that the new battery may have enough charge for some calls.

Make a call

•Press/FLASH or/SPEAKER to ensure there is a dial tone, then dial the telephone number.

-OR-

For predialing:

•Dial the number (press MUTE/REMOVE or OFF/CLEAR to backspace, or press and hold REDIAL/PAUSE to insert a pause).

•Press /FLASH or /SPEAKER if you want to use the speakerphone function.

Receive a call

•Press /FLASH or /SPEAKER or any dialing keys (0-9, #, *) if you want to use the speakerphone function.

End a call

•Press OFF/CLEAR, or put the handset in the telephone base or charger.

STEP 5 Turn the answering system on and off

The answering system must be turned on to function. If the answering system is turned off, the telephone base light will be off.

To turn on/off the answering system:

•Press ANS ON/OFF to choose between on and off.

STEP 6 Record outgoing announcement (optional)

The telephone is pre - programmed with the announcement “Hello, please leave a message after the tone.” To replace the default announcement:

•Press ANNC and the system announces “Announcement, press PLAY or press RECORD.”

•Press RECORD to record, and the system announces “Record after the tone. Press STOP when you are done.”

•After the tone, speak towards the microphone at the front right of the telephone base from about nine inches away.

•Press /PLAY/STOP when finished and the answering system will automatically playback the newly recorded announcement.

STEP 7 Charge the battery

•The battery may have enough charge for a short call. For best performance, charge the battery for at least 16 hours.

•To charge the handset, place it in the telephone base or charger.

•The CHARGE light on the telephone base or charger will be on when the handset is properly positioned. See Troubleshooting in the user’s manual if the CHARGE light is not on.

For installation and use of the belt clip and the wall mount bracket, please consult the user’s manual.

IMPORTANT!

If your product is not working properly:

•Refer to the Troubleshooting section of your user’s manual.

•Visit our website at www.vtechphones.com, or in Canada, www.vtechcanada.com.

•Call our customer service at 1 (800) 595-9511 or 1 (800) 267 7377 in Canada.

96-006299-020-100 issue 0