White Outdoor Z - 180, Z - 180L, Z - 200 manual Speed Control BAR

Page 10

When the engine is running, the throttle is set and the Drive Handles are moved from the neutral position, the unit moves in accordance with the driver’s input (push, pull or both). When the driver releases the handles they immediately return towards the neutral position and the unit will slow and stop moving (while the engine continues to run).

The rear wheels propel and steer the unit. The Left Drive Handle controls the Left rear wheel and the Right Drive handle controls the Right rear wheel. Push a handle forward and the respective wheel turns forward. Pull a handle back and the respective wheel turns in reverse.

Each Drive handle has a range in the forward position (push) and the reverse position (pull). If a Drive Handle is moved to the full position (until it stops) the rear wheel turns as fast as the throttle is set. Positions between neutral and full are proportional across the range based on the throttle setting. The Drive Handles can be moved together in the same direction or independent of each other in any combination (i.e. Left push, Right pull).

NOTE: The Drive Handles will return toward neutral when released, but they should be placed in neutral by the driver. If the Drive Handles are not placed in neutral, the tractor may creep.

Speed Control

Bar

Wing Nut

Figure 9

SPEED CONTROL BAR

The Speed Control Bar is connected to the console with two wing nuts. (See Figure 9). It is used as a grab bar for entry or exit from the tractor and allows for pre-set maximum travel speed.

•Loosen the two wing nuts located on either side of the plastic console.

•Rotate speed control bar to desire location.

•Tighten wing nut to secure speed control bar.

NOTE: Limit loosening the wing nuts to 1 1/2 turns. This will insure proper assembly of the screw not visible on the other side of the plastic console. Refer to parts book if screw fell and wing nuts are no longer tightening.

The Speed Control Bar also aids the drive handles in making “perfect U-turns”. Grasping both Drive Handles and the Speed Control Bar at the same time to move forward, release the Left Drive Handle to turn left and then re- grasp to continue straight ahead or release the Right Drive Handle to turn right. Refer also to the Quick Reference Chart located in the Operation Section.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Important Read Safety Rules and Instructions Carefully OPERATOR’S ManualCalling Warranty Service Finding Your Model NumberImportant Safe Operation Practices General OperationDo not ServiceSlope Operation ChildrenSafety Labels Found On Unit GaugeSlope Controls Power TAKE-OFF PTO SwitchHOUR/RPM Meter IGNITION/LIGHT Switch Lift HandleParking Brake Throttle Lever and Choke LeverDrive Handles Speed Control BAR Indicator Panel Seat Adjustment LeverOperating Guidelines OperationBefore Operating Starting the EngineOperating the Choke Lever Starting a Flooded EngineStopping the Engine Operating the Throttle LeverQuick Reference Chart Page Driving on Slopes Operating the PTO Power Take OFF ClutchDriving the Z-SERIES Stopping the Z-SERIESPushing Your Unit Adjusting the Seat Position AdjustmentsAdjusting the Mower Deck Height Checking the Brake AdjustmentAdjusting Brake Force Frame Measure GapSteering Adjustment Page Lubrication Grease Point When to Grease Type of GreaseOil Check Change Capacity Type Grease Point Locations Engine Compartment MaintenanceAccessing the Engine Prop rod on left hand side of latchChecking Hydraulic OIL Level Fuel TankCheck oil Checking the Hydraulic OIL If hydraulic oil level is ThenAdding Hydraulic OIL Draining Hydraulic OILReplacing the Head Lamp Bulb Removing the Battery Battery MaintenanceCharging the Battery Installing the BatteryBattery Storage Clean the BatteryTires Mower Decks When either side is higher than When either side is lower thanLeveling the Mower Deck Removing the Mower Deck If Mower Deck is ThenTension Bar Installing a NEW Mower Deck Belt Installing the Mower Deck Mower Deck Belt RoutingCutting Blade Care Removing a BladeLubrication of Mower Deck Installing a BladeInstalling a NEW Drive Belt Removing the Drive BeltStorage Mowing Avoiding StreakingTrouble Shooting Guide Trouble Possible Causes Corrective ActionPage Page MANUFACTURER’S Limited Warranty for

Z - 180, Z - 180L, Z - 200 specifications

The White Outdoor Z - 180, Z - 180L, and Z - 200 are prominent entries in the outdoor power equipment market, renowned for their robust features and advanced technologies. These models represent a classic blend of power, efficiency, and user-friendly design tailored for residential and commercial users alike.

Starting with the Z - 180, this model shines with its exceptional maneuverability and compact design, making it ideal for smaller lawns and gardens. It is powered by a high-performance engine that delivers impressive torque and speed. The Z - 180 features a 42-inch cutting deck, which allows for effective grass cutting in tight spaces. Its easy-to-adjust cutting height enables users to customize the mow according to various grass types and conditions. The model’s hydrostatic transmission ensures a smooth and responsive driving experience, allowing users to navigate obstacles effortlessly.

Next, the Z - 180L is an upgraded version of the Z - 180, featuring a larger cutting deck of 48 inches, which makes it suitable for slightly larger properties while still maintaining a compact footprint. One of the defining characteristics of the Z - 180L is its enhanced comfort features, including a spacious operator platform and a high-back seat. These enhancements minimize operator fatigue during extended use. Additionally, the Z - 180L employs advanced air filtration technology, which helps to keep the engine clean and efficient, enhancing its longevity and performance.

In the line-up, the Z - 200 stands out with its powerful engine options and advanced features that cater to both professional landscapers and serious homeowners. The Z - 200 comes equipped with a robust 60-inch cutting deck that enables fast and efficient mowing of larger areas. The model’s powerful hydraulic system provides maximum performance and responsive handling, essential for tackling challenging terrains. The ergonomic controls and adjustable steering ensure a comfortable operation even during long mowing sessions.

All three models highlight White Outdoor's commitment to durability, featuring heavy-duty frames and high-quality materials that withstand rigorous use. The ease of maintenance across these models is another focal point, with accessible engine components and user-friendly design facilitating routine checks and servicing.

In conclusion, the White Outdoor Z - 180, Z - 180L, and Z - 200 are exceptional lawn care machines that stand out in the market for their power, efficiency, and user-centric features. Whether for small gardens or expansive landscapes, these mowers provide reliable performance, comfort, and advanced technology designed to meet the varying needs of outdoor enthusiasts.
Top Page Image Contents