Weslo SPRW52464 user manual Using the Daybreak, Priming the SPA JET Unit, Plugging in the Daybreak

USING THE DAYBREAK

The DAYBREAK is designed for up to four adults. The six water jets can be regulated to provide a relaxing massage to sooth away stress, and the strength of the water massage can be adjusted by the air control. The DAYBREAK holds 170 gallons of water and offers an automatic, programmable heating (70¡F to 104¡F) and filtration system.

The guidelines below explain how to properly use the DAYBREAK. Follow these guidelines to maintain the DAYBREAK for your long-term enjoyment.

PRIMING THE SPA JET UNIT

The water pump in the
spa jet unit must be
primed before you use
the DAYBREAK the
	Primer
first time. You must
	Cap
also prime the pump
before using the unit
each time you re-fill
the DAYBREAK.

To prime the spa jet unit, remove the primer cap from the console. Fill the spa jet unit with at least 64 oz. of water. Replace and tighten the primer cap. IMPOR-

TANT: The spa jet unit may be seriously damaged if the pump is not properly primed, or if the primer cap is not replaced and fully tightened.

PLUGGING IN THE DAYBREAK

Once the DAYBREAK is filled with enough water to cover the water jets and the pump has been primed, the power cord can be plugged in and the spa jet unit can be turned on. Note: The first time the power cord is plugged in, the spa jet unit will turn on automatically.

When connecting the power cord, plug the power cord directly into a grounded circuit capable of carrying 15

Grounded circuit capable of carrying 15 or more amps

Test and Reset

Buttons

GFCI

or more amps. No other appliance should be on the same circuit. Replace the power cord immediately if it becomes damaged.

The power cord is equipped with a Ground Fault Circuit Interrupter (GFCI), located at the end of the power cord. You should always test the GFCI before using the DAYBREAK.

First, turn on the DAYBREAK by pressing the power button on the console. Once the unit is running, press the GFCI ÒtestÓ button. The DAYBREAK should shut off. Press the ÒresetÓ button. The DAYBREAK should resume normal operation. If the DAYBREAK contin- ues to run after the ÒtestÓ button is pressed, then the GFCI is damaged. Do not use the DAYBREAK until the GFCI has been repaired or replaced by a qualified electrician.

STARTING THE DAYBREAK

Once you have tested the GFCI, you should verify the water flow from the pumping unit. Set the air control on the console to the lowest setting (see USING THE CONSOLE on the next page). The pumping unit will heat the water as it pumps. Cover the DAYBREAK with the spa cover. The spa cover must be tight. The water will heat at about 1.5¡F an hour with the cover on. If you are using the DAYBREAK indoors, and the room temperature is maintained at 70¡F, it will take approximately 36 to 48 hours for the water to reach the set temperature.

The temperature and water flow can be set or changed by the controls on the console (see USING THE CONSOLE on the next page).

TESTING AND TREATING THE WATER

The DAYBREAK comes with a starter chemical pack for maintaining the water in the spa. Disregard the directions on the individual packages of ÒQUICK pHix It DOWNÓ and ÒQUICK pHix It UP.Ó However, the directions on the bottle of ÒNon-chlorine ShoxÓ and ÒBromine BaseÓ are correct. Always keep the chemi- cals away from children and pets.

The first time you use the spa, you should test and treat the water. Once you have verified that the spa jet unit is functioning properly, and have allowed the water to circulate for a while, you should remove the spa cover and add 1/3 of the ÒBromine BaseÓ bottle, and 1/3 of the ÒNon-chlorine ShoxÓ bottle to the water in the spa. Allow the water to circulate for five min- utes. You should now test the pH level of the water. You will need a pH test kit (not included), which can

12