SECTION 9: TROUBLE SHOOTING GUIDE
Trouble | Possible Cause(s) | Corrective Actions | ||
|
|
|
|
|
Engine fails to | 1. | Blade control handle disengaged. | 1. | Engage blade control handle. |
start | 2. | Spark plug wire disconnected. | 2. | Connect wire to spark plug. |
| 3. | Dirty aircleaner. | 3. | Refer to the engine manual packed with your unit. |
| 4. | Primer button not depressed. | 4. | Refer to the engine manual packed with your unit. |
| 5. | Throttle control lever not in correct | 5. | Move throttle lever to FAST or START position. |
|
| starting position (if so equipped). |
|
|
| 6. | Fuel tank empty or stale fuel. | 6. | Clean fuel line. |
| 7. | Blocked fuel line . | 7. | Clean, adjust gap or replace. |
| 8. | Faulty spark plug. | 8. | Refer to the engine manual. |
| 9. | Engine flooded. | 9. | Wait for a while and crank the engine. |
Engine runs | 1. | Unit running in START position. | 1. | Move throttle lever to FAST position. |
erratic | 2. | Spark plug wire loose. | 2. | Connect and tighten spark plug wire. Check spark plug |
|
|
|
| for fouling. |
| 3. | Blocked fuel line or stale fuel. | 3. | Clean fuel line; fill tank with clean, fresh gasoline. |
| 4. | Carburetor out of adjustment. | 4. | Refer to the engine manual packed with your unit. |
Engine | 1. | Engine oil level low. | 1. | Fill crankcase with proper oil. |
overheats | 2. | Dirty aircleaner. | 2. | Refer to the engine manual packed with your unit. |
| 3. | Air flow restricted. | 3. | Stop engine and disconnect spark plug wire. Remove |
|
|
|
| blower housing and clean. |
| 4. | Carburetor not adjusted properly. | 4. | Refer to the engine manual.. |
Occasional skip | 1. | Spark plug gap too close. | 1. | Adjust gap to .030". |
(hesitates) at | 2. | Carburetor idle mixture | 2. | Refer to the engine manual packed with your unit. |
high speed |
| adjustment improperly set. |
|
|
Idles poorly | 1. | Spark plug fouled, faulty or gap | 1. | Reset gap to .030" or replace spark plug. |
|
| too wide. |
|
|
| 2. | Carburetor not adjusted. | 2. | Refer to the engine manual. |
Excessive | 1. | Cutting blade loose or | 1. | Tighten blade and adapter. Balance blade. |
vibration |
| unbalanced. |
|
|
| 2. | Bent cutting blade. | 2. | See an authorized service dealer. |
Mower will not | 1. | Engine speed too low (not | 1. | Set throttle between 3/4 and full throttle. |
mulch grass |
| applicable in mowers with fixed |
|
|
|
| throttle) |
|
|
| 2. | Wet grass. | 2. | Wait until later to cut. |
| 3. | Excessively high grass. | 3. | Mow once at a high cutting height, then mow again at |
|
|
|
| desired height .. |
Uneven cut | 1. | Wheels positioned incorrectly. | 1. | Place all four wheels in same height position. |
| 2. | Dull blade. | 2. | Sharpen or replace blade. |
NOTE: For repairs beyond the minor adjustments above, contact your local authorized service dealer.
16