Assembling Your Lawn Mower | Yard Machines 810, 829 specification

SECTION 3: ASSEMBLING YOUR LAWN MOWER

IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your mower.

NOTE: Reference to right or left hand side of the mower is observed from the operating position.

Removing Unit From Carton

•Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.

•Remove loose parts if included with unit (i.e., operator’s manual, oil, etc.)

•Cut along corners, lay carton down flat, and remove packing material.

•Roll or slide unit out of carton and check carton thoroughly for loose parts.

Disconnecting Spark Plug Wire

•Before setting up your lawn mower, disconnect the spark plug wire from the spark plug and ground to a bolt on the engine. See Figure 1.

Stud
	Spark Plug
	Wire
Spark
Plug Wire	Spark Plug

Figure 1

Attaching Handle to Mower

•For shipping purposes, your mower is set with the rear wheels in the lowest cutting position. Raise the rear wheels to the highest setting for assembly of handle.

•Remove the hairpin clips from the outer hole in the weld pins on the handle mounting brackets.

•Lift the handle and attach by placing the bottom holes in the lower handle over the weld pins on the handle mounting brackets. Make sure the lower handle is seated securely into the handle mounting brackets.

•Pull up on the upper handle to raise it into the operating position. Tighten the wing nuts on each side of the handle.

NOTE: Your mower is shipped with the handle in the higher height position. If you wish to lower the height of the handle, refer to the Adjustment Section at this time.

•Secure the handle assembly by placing the hairpin clips in the inner hole on weld pins.

•The rope guide is attached to the right side of upper handle. Loosen the wing nut which secures the rope guide.

•With the spark plug disconnected and grounded, hold the blade control handle against the upper handle and pull the starter rope out of the engine. Release the blade control handle. Slip the starter rope into the rope guide and tighten the wing nut.

•Make certain all nuts and bolts are tightened securely.

Attaching Bag To Mower

•Swing open the chute door on the catcher panel and hold in this position. See Figure 2.

Hook On

Frame

Grass

Catcher

Frame

Channel On	Chute
Mower	Door

Rear Discharge

Chute Assembly

Figure 2

•Slide the frame of the grass catcher down into the channels on each side of the mower. The hooks on the frame go over the panel on the discharge chute.

•To remove the grass catcher, hold the chute door and lift the grass catcher straight up using the handle.

Converting Mower To Side Discharge

•Remove the rear discharge chute assembly by removing two wing nuts. Lift up on the two bottom corners of the discharge chute assembly and slide it off the deck.

•Attach the side chute deflector by first placing it over the rear bolt in the side of the deck. Then slide the notch in the top of the deflector around the shoulder bolt on top of the deck.

•Slide the notch in the side of the deflector around the front bolt in the side of the deck. Secure the front of the chute deflector to the bolt on the side of the deck with one wing nut. See Figure 3.

810, 829 specifications

The Yard Machines 829,810 is a highly regarded piece of outdoor power equipment designed to tackle a variety of landscaping tasks with ease and efficiency. This robust model is particularly popular among homeowners and garden enthusiasts for its versatility and user-friendly features.

One of the standout characteristics of the Yard Machines 829,810 is its powerful engine. Equipped with a reliable and efficient four-stroke engine, this model ensures dependable performance in various conditions. The engine is designed to provide ample torque, enabling it to handle troublesome weeds, thick grass, and even light brush with minimal effort. This power translates into a highly productive machine that can save users valuable time during yard maintenance.

The cutting deck on the Yard Machines 829,810 is another key feature. Designed for durability and effectiveness, the cutting deck provides multiple height adjustments, allowing users to customize their mowing experience according to the terrain and the type of grass. The width of the deck facilitates a clean and even cut, ensuring that your lawn remains in pristine condition.

In terms of technology, the Yard Machines 829,810 incorporates advanced features such as a straightforward pull-start mechanism, which enhances usability, particularly for those who may be less experienced in handling power equipment. The machine’s lightweight design facilitates easy maneuverability, while the built-in safety features ensure a secure operation.

Additionally, the Yard Machines 829,810 is designed with comfort in mind. The ergonomic handle provides a secure grip, reducing strain during prolonged use, while the adjustable height settings cater to users of varying statures.

For those who prioritize maintenance, the easy-access design of the engine and cutting deck simplifies routine upkeep, ensuring longevity and reliability. The robust construction of this machine not only enhances its durability but also guarantees it can withstand the rigors of regular lawn care.

In conclusion, the Yard Machines 829,810 stands out as a reliable and efficient lawn care tool, combining power, technology, and user-friendly design. Whether tackling a residential lawn or managing a larger landscaping project, this model is an excellent addition to any outdoor toolkit, catering to both novice and experienced users alike.