Woodstock W2007, W2005, W2006 instruction manual Fence, Foot Rails, Mounting the extension legs

Page 10

Fence

1.Raise the lock handle up to release the fence locking tab and place the fence down on the rails.

2.Make sure the angle bracket of the fence assembly fits easily into the slot created by the front rail bracket and rectangular tube.

•If any binding is experienced, loosen the rail mounting bolts and adjust the rails.

3.Install the fence, and check to see that it slides smoothly along the rails without binding or catching on the table surface.

•If any binding is experienced, loosen the rail mounting bolts and adjust the rails.

4.Make sure you keep the rail support pad free of debris and dirt. This pad is pre-positioned so that it slides along the top of the rail or the top of the table. The rear rail support pad is located on the underside of the fence. See Figure 5.

Rear Rail

Support Pad

Fence Shown Upside Down

Figure 5. Rear rail pad location.

7-Foot Rails

The W2006/2007 extended 7' rail set for the SHOP FOX® Classic Fence increases the rip capacity to the right of the blade to 54''.

These are mounted in the same manner as the standard rails. The long rail set also includes legs which provide added stability for the table saw/fence assembly when large or heavy work is positioned on the table.

Mounting the extension legs

1.Attach rails according to the rail installation instructions on page 6 & 7.

2.Thread a 1⁄2" hex nut onto each foot and thread a foot into the bottom of each leg.

3.Loosely bolt a brace to each of the legs with a 3⁄8-16 x 3⁄4" hex bolt and three 3⁄8" washers. Place two of the washers between the leg and the brace.

4.Position the legs as shown in Figure 6 and insert two 1⁄4-20 x 1⁄2" hex bolts with washers through each rail and loosely thread them into the legs.

5.Rotate the braces up and thread a 3⁄8-16 x 5⁄8" hex bolt with a washer through each rail and into the braces.

6.Place a level on the rails and adjust the feet until the rails are level, then tighten the hex nuts on the feet against the bottom of the legs.

7.Tighten all of the bolts.

-8-

Shop Fox® Classic Fence

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models Page Contents Introduction GeneralWarranty Safety Precautions BAD Habits are DANGEROUS. Review all safety procedures oftenModel W2005 InstallationInventory Model W2006Rail Installation Mounting the Back RailMounting The Front Rail Mounting The Front Rail TubeFoot Rails FenceMounting the extension legs Extension Table Constructing the extension tableMagnetic Switch Blade GuardAdjustments Fence ParallelismFence-to-Table Clearance Lock HandleScale and Cursor Scale location for right-side blade useDrilling Through-Holes Drilling and Tapping Mounting HolesDrilling Holes In the Rails Using Board Buddies Using a Wood Fence FacingOperations W2005 Fence Parts Diagram W2005 Standard Rail Parts Diagram W2007 Leg and 7 Rail Parts Diagram W2005 Parts List W2007 Parts ListPage
Related manuals
Manual 24 pages 12.24 Kb Manual 24 pages 12.24 Kb

W2007, W2006, W2005 specifications

The Woodstock W2005, W2006, and W2007 models represent a significant evolution in the Woodstock acoustic guitar lineup, showcasing a commitment to quality craftsmanship and innovative technology that appeals to both beginner musicians and seasoned players alike.

The Woodstock W2005 model debuted in 2005, marked by its elegant design and warm, resonant tone. One of its standout features is the solid spruce top, which contributes to a rich sound that ages beautifully over time. The back and sides are typically crafted from mahogany, providing enhanced projection and a balanced tonal character. The W2005 comes equipped with a comfortable neck profile, making it easier for players to navigate the fretboard regardless of their skill level. Another significant characteristic of the W2005 is its premium rosewood fingerboard, known for its smooth playability and aesthetic appeal, topped with simple yet classic dot inlays.

Building on the success of the W2005, the Woodstock W2006 introduced several enhancements. This model features an upgraded Fishman pickup system, allowing for amplified performances without sacrificing the natural acoustic sound. The W2006 also showcases a more diversified material selection, with an emphasis on sustainable sourcing, ensuring that players can enjoy their instrument while being environmentally responsible. The bracing pattern in the W2006 was re-engineered to deliver even more resonance and volume, resulting in a well-rounded sound perfect for a variety of musical styles.

By the time the Woodstock W2007 was released, the brand had honed its design and technological aspects further. The W2007 is characterized by its stunning visual aesthetics, often featuring unique inlays and a glossy finish that not only enhances its beauty but also adds durability. The soundboard of the W2007 is crafted using a combination of solid woods, with some variations offering premium options like cedar. This model emphasizes tonal clarity and dynamic range, ideal for fingerstyle playing or strumming chords with equal finesse.

In summary, the Woodstock W2005, W2006, and W2007 each brought distinct features and advancements, catering to the diverse needs of musicians. From solid wood construction and sustainable practices to advanced electronics and striking finishes, the Woodstock series reflects an evolution of craftsmanship and a dedication to creating instruments that inspire creativity and passion in every performance.
Top Page Image Contents