Stiga 4WD Installation of 107 M HD, 121 M, Installing 92/107 M, Tyre pressure, Basic setting

ENGLISH

3.2 Installation of 107 M HD, 121 M

1.Place the cutting deck in position in front of the machine.

2.Install the following components on both wheel axles:

•Washer (3:B).

•Deck mount (3:C).

•Washer (3:B).

•Circlip (3:A).

3.Remove the pins on both sides. See fig. 7:I and fig. 13.

4.Screw the arms into each other. See fig. 4.

5.Suspend the cutting deck in the implement lift- er. See fig. 17.

6.If the deck has electrical cutting height adjust- ment, connect the cable to the machine’s front right socket. See fig. 15.

3.2.1 Belt, 107 M HD, 121 M

The cutting deck’s rear section should rest on the floor (it should not be lifted or secured).

Install the belt as follows:

1.Set the cutting height in the centre position

2.Remove the belt cover. See fig. 8 and 10. The number in the figure indicates the key width.

3.Locate the belt around the machine’s belt pulley (16:M).

4.Force the belt onto the cutting deck’s belt pul- ley.

5.Grip the belt tensioner’s lever with your left hand. Pull the lever and apply the tensioner to the outside of the belt with your right hand. See fig. 16.

6.Fit the belt cover. See fig. 8 and 10.

7.Lift up and secure the rear section of the cutting deck.

107 M HD on machines with 17” wheels: Install the pins in the third hole from the top. See fig. 13.

107 M HD on machines with 16” wheels: Install the pins in the fourth hole from the top. See fig. 13.

121 M: Lift up and install the pins (7:I).

3.3 Installing 92/107 M

1.Place the cutting deck in position in front of the machine.

2.Install the following components on both wheel axles:

•Washer (11:B).

•Deck arm (11:D).

•Washer (11:B).

•Circlip (11:A).

3.Install the deck arms in the cutting deck’s front corners. After tightening, it should be possible to move the rear section of the cutting deck free- ly up and down.

4.Suspend the cutting deck in the implement lift- er. See fig. 17.

3.3.1 Belt, 92/107 M

The cutting deck’s rear section should rest on the floor (it should not be lifted or secured).

Install the belt as follows:

1.Set the maximum cutting height.

2.Remove the belt cover. See fig. 10. The number in the figure indicates the key width.

3.Locate the belt around the machine’s belt pulley (16:M).

4.Force the belt onto the cutting deck’s belt pul- ley.

5.Grip the belt tensioner’s lever with your left hand. Pull the lever and apply the tensioner to the outside of the belt with your right hand. See fig. 16.

6.Fit the belt cover. See fig. 10.

7.Lift up the cutting deck so that it locks in the catches (12:L).

3.4 Tyre pressure

Adjust the air pressure in the tyres as follows: Front: 0.6 bar (9 psi).

Rear: 0.4 bar (6 psi).

3.5 Basic setting

In order for the cutting deck to cut optimally, the correct basic setting is required. The deck is in the basic setting when its rear edge is 5 mm above its front edge. This means that the deck is inclined forwards.

Carry out basic setting as described below.

3.5.1Basic setting, 110/125 Combi Pro, 107 M HD

The deck is in the basic setting when the actions under 3.1.1 and 3.2.1 have been carried out.

35