Using the Machine

ENGLISH

8.Install the height setting strut (8) on the angle

(W). Position the spacer (K) on the screw (E). Insert the screw with the spacer through the hole in the height setting strut and into the hole in the angle. Lock in place with the locking washer (J) and the nut (H).

9.Attach the other end of the height setting strut

(8) to the height setting arm (7). Position the groove in the height setting strut opposite the square hole in the arm.

10.Screw into place with a carriage bolt (D), a flat washer (I) and the locking wheel (T).

11.See fig. 5. Install the two securing arms (5) on the outside of the brush unit. Screw the securing arms into the rear, lower holes with four screws

(B) and four locking nuts (F).

NOTE! The grooves in the securing arms must be facing up.

12.Install the hitch pin (U) and the two spacers (L) in the connecting rod. Lock with the locking pins (N).

Assembling the hopper bag

Figures and letters in brackets refer to the figures.

1.See fig. 6, 7. Insert the left-hand, upper hopper bag tube (1) in the hopper bag flap. Start at the cut-out in the middle of the hopper bag’s upper section. The holes in fig. 6 must be facing down.

2.Install the right-hand, upper hopper bag tube (1) in the same way and press the tubes together.

3.Secure the tubes by pressing in a plastic plug

(R) through the holes.

4.See fig. 7. Locate the holes in the sides of the two upper hopper bag tubes. These will be used later.

5.See fig. 9. Assemble the two lower hopper bag tubes (3, 4).

6.See fig. 9. Secure the tubes by pressing in a plastic plug (R) through the holes.

7.Position the lower hopper bag tubes inside the hopper bag.

8.See fig. 10. Assemble the two upper and lower hopper bag tubes’ ends using the pins (Q) and the locking pins (M).

9.See fig. 11. Attach the hopper bag’s front strut to the lower hopper bag tubes using the pins (O) and the locking pins (M).

10.See fig. 12. Snap the hopper bag together around the bag tubes using the snap fasteners.

The hopper bag supports are made of powerful spring steel. Wear protective goggles during assembly.

11.See fig. 13. Tension the two sprung struts (11) in the rear part of the hopper bag.

12.See fig. 14. Locate the holes in the sides of the hopper bag and make holes with an awl or sim- ilar.

13.See fig. 15. Install the hopper bag locks (X), the pins (P) and the locking pins (M) in both sides of the hopper bag.

NOTE! The hopper bag locks must be able to move about freely.

14.See fig. 16. Install the line (15).

15.Install the wind protection on the rear upper section of the hopper bag.

16.See fig. 17, 18. Install the hopper bag on the brush unit.

Operating

Be careful when driving on slopes.

The vehicle’s braking characteristics and stability can be affected by installed accessories or optional extras. Be particularly careful when driving on slopes.

Hopper bag height

Set the hopper bag so that its bottom is horizontal and is 8-10 cm above the ground when driving. See point 3 under “ASSEMBLY”.

Brush height setting

Set the brushes to the correct height by undoing the locking wheel and then moving the arm up or down, see fig. 19. If the arm is moved down, the brushes are raised. The best results are obtained if the brushes sweep the top of the grass without touching the soil below. The brushes must not be lowered so much that the collector’s wheels slide or slip.

Speed

•Test which speed produces the best results.

•The speed should be selected so that the grass is thrown to the rear part of the hopper bag.

•Recommended speed: 4.8 - 6.4 km/h.

8211-1227-02 specifications

The Stiga 8211-1227-02 is an innovative lawn mower designed to deliver efficient grass cutting performance while ensuring ease of use and durability. This machine is engineered with a variety of features that cater to both professional landscapers and homeowners looking for a reliable tool for maintaining their lawns.

One of the standout characteristics of the Stiga 8211-1227-02 is its powerful engine. Equipped with a robust petrol motor, this lawn mower provides excellent cutting power even in challenging conditions. The engine is designed for high efficiency, ensuring that users can complete their mowing tasks with minimal fuel consumption.

The mower is designed with a 46 cm cutting width, making it suitable for medium to large-sized lawns. This width enables a faster mowing process without sacrificing precision. Additionally, the cutting height on the Stiga 8211-1227-02 is adjustable, allowing users to select the perfect height for their grass type and desired finish. The cutting heights can typically be set between 25 to 80 mm, giving flexibility and control over the mowing results.

Another notable feature is the robust chassis construction, which is made from high-quality materials that withstand the rigors of frequent use. The design is not only functional but also includes ergonomic handles that ensure comfort during operation. These handles can often be adjusted for different user preferences, making it versatile for various operators.

The Stiga 8211-1227-02 also incorporates advanced technologies that enhance its cutting performance. Its mulching capability is particularly impressive, allowing grass clippings to be finely chopped and returned to the lawn, promoting natural fertilization and a healthier turf. This technology helps to reduce waste and lessens the need for bagging, offering an environmentally friendly mowing option.

Moreover, this model typically features an easy-start system that simplifies the ignition process, enabling quick and hassle-free operation. The inclusion of large rear wheels enhances maneuverability, especially on uneven terrain, providing the user with improved stability and control.

With its combination of power, efficiency, and user-friendly features, the Stiga 8211-1227-02 is an excellent choice for those seeking a high-quality lawnmower that meets the demands of both professional and residential mowing. Whether you have a sprawling yard or a quaint garden, this mower promises to deliver exceptional grass cutting results time after time.