Maintenance

GB	ENGLISH

2.If the lawn mower is left unattended to, remove the lead from the spark plug. Also remove the starter key (*).

If the start/stop loop no longer works, stop the engine by removing the lead from the spark plug. Immediately take the lawn mower to an authorised work- shop for repairs.

REAR WHEEL DRIVE (*)

Engage the drive by pressing coupling clamp I against the steering handle. Disengage the drive by releasing coupling clamp I (fig. 10).

CUTTING HEIGHT

Shut off the motor before adjusting the cutting height.

Do not set the cutting height so low that the blade/blades can hit uneven ground.

The mower is fitted with a single lever control for adjusting the cutting height. Pull the lever out- wards and adjust the cutting height to the position which is most suitable for your lawn (fig. 11).

NOTE! When the machine is used for "Multi- clip", the two lowest cutting heights must not be used. The "Multiclip" function does not work if the grass is cut too short.

Neither the motor nor the lawn mower may be serviced before the ignition ca- ble is removed from the spark plug.

Stop the motor and remove the spark plug cable if the mower is to be lifted, e.g. with transportation.

If the lawn mower needs to be tilted it should be tilted so that the spark plug face upwards. Tilt the lawn mower when the fuel tank is empty.

CLEANING

After each time it is used the mower should be cleaned. This is particularly important on the un- derside of the mower casing. Wash out with the garden hose. The mower will then last longer and function better. Note! High pressure washing units should not be used.

If grass has dried on to the cutterhead casing it can be removed by scraping. If necessary, give the un- derside a touch of paint to prevent rusting.

Clean the silencer and the surrounding area regularly to remove grass, dirt and flammable waste products.

You should clean the inside of the drive wheels (*) once every season. Remove both wheels. Brush or blow-clean the gear and the wheels' gear ring from grass and dirt. Refit the wheels (fig. 12).

PROTECTIVE GRILLE

Clean the protective grille F to remove any grass and dirt after each time the machine is used to pre- vent the engine from becoming damaged as a re- sult of overheating (fig. 13, 14).

COOLING SYSTEM

The engine is air-cooled. Grass and dirt can easily clog the cooling system and damage the engine. The cooling system should be cleaned at least once a season or after every 100 hours of operation. Clean more often if you mow in dry grass.

Briggs & Stratton model. LS45:

Remove the three screws A (fig. 13) and lift away the fan housing. Clean the area inside the line (fig. 15).

On LS45 engines, the screws A can be more easily reached if the engine cover is removed first.

Briggs & Stratton model. ES40:

Remove the protective grille and clean the marked area (fig. 16).

LUBRICATING THE DRIVESHAFT (*)

You should grease the key on the driveshaft once every season. Remove the wheel (hub cap, screw and washer). Then remove the E-circlip and wash- er to enable the gear to be removed from the shaft. Grease the key with universal grease.

Refit the key (different key fitments on right- and left-hand sides, see fig. 17, 18). Install the gear so that the L mark will be facing outwards on the left- hand side, and the R mark facing outwards on the right-hand side (mower viewed from behind).

45, 45S, 45SE specifications

The Stiga 45SE, 45S, and 45 lawn mowers have gained popularity among gardening enthusiasts and professionals alike due to their robust features, advanced technologies, and user-friendly characteristics. Designed for efficient and effective lawn care, these cutting-edge machines are tailored to meet diverse mowing needs while ensuring ease of use and comfort.

One of the standout features of the Stiga 45 series is the powerful engine. Equipped with reliable and efficient motors, these mowers offer sufficient power to tackle various grass types and mowing conditions. The 45SE model stands out with its electric start, providing convenience and eliminating the hassle of pulling cords. The engines are designed to maintain optimal performance while minimizing fuel consumption and emissions, promoting eco-friendly operation.

The cutting deck is another area where Stiga excels. The 45SE, 45S, and 45 models come with a generous cutting width, ranging between 40 to 45 cm, allowing for efficient mowing of both small and medium-sized lawns. The height adjustment feature enables users to choose from multiple cutting heights, ensuring a pristine cut tailored to individual preferences and lawn requirements.

An innovative technology featured in these mowers is the Multiclip system, which finely shreds grass clippings, allowing them to decompose and naturally fertilize the lawn. This not only provides a clean finish but also reduces the need for additional fertilizers, promoting a healthier lawn ecosystem.

User comfort is a priority in the design of these mowers. The ergonomic handles and lightweight construction make maneuverability easy, even in tight spaces. Additionally, the adjustable handlebars allow operators of varying heights to find their optimal mowing position, reducing fatigue during extended use.

The Stiga 45 series also incorporates safety features, such as a safety key and automatic stop, ensuring that the mower is only operational when intended, thus preventing accidents. This is essential for families with children and pets around.

In conclusion, the Stiga 45SE, 45S, and 45 lawn mowers represent a blend of power, efficiency, and user-centric design. With advanced engine technology, versatile cutting options, and ergonomic features, these models are perfect for anyone looking to maintain a beautiful lawn with minimal effort. Whether you are a seasoned gardener or a novice, the Stiga 45 series provides the tools necessary to achieve a well-groomed garden efficiently.

ENGLISH