Stanley Black & Decker GTR20 user manual Cold Weather Startup, Shutdown

Page 13

OPERATION

FOR 5 GPM OPERATION

For 5 gpm operation, select mode of operation with the Throttle Control switch, either auto-idle-on or the auto- idle-off position. Move the flow selector switch to the 5 gpm position.

Note:

If operating both 5 gpm circuits move both flow se- lector switches to the 5 gpm position. Both 5 gpm circuits are independent from each other and can be operated on its own.

When finished operating the tool, move one or both flow selector switches to the OFF position.

FOR 10 GPM OPERATION

For 10 gpm operation, select mode of operation with the Throttle Control Switch, either auto-idle-on or the auto- idle-off position. Move both flow selector switches to the 10 gpm position.

When finished operating the tool, move both flow selec- tor switches to the OFF position.

Note:

Either set of couplers can be used for the 10 gpm circuit, but DO NOT use two separate tools when in the 10 gpm operation mode.

COLD WEATHER STARTUP

1.Use the procedures described under "STARTUP" and then follow the procedure below.

2.Hydraulic fluids are thicker in cold weather. There- fore, it is recommended that the engine be run at low idle long enough to bring the fluid temperature up to a minimum of 50°F/10°C.

3.If the tools and tool hoses are cold, it is recom- mended to allow hydraulic fluid to circulate through the tool hoses until warm before using the tool.

SHUTDOWN

1.Ensure the flow selector switches are in the OFF po- sition (center position).

2.Unless already at idle the power unit should return to idle. This may take a few seconds for the unit to react due to a built-in program delay.

3.Allow the engine to idle for approximately one minute and move the Ignition Switch to the OFF position.

GTR20 User Manual ◄ 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents GTR20 Hydraulic Power Unit Page Table of Contents Local Safety Regulations Safety SymbolsSafety Precautions Tool Stickers Hydraulic Hose Requirements Hose Safety TagsTAG Shown below is Attached to Conductive Hose Tool to Hydraulic Circuit Hose Recommendations Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsPreparation for USE OperationValve Block BatteryStartup ControlsThrottle Control AUTO-ONShutdown Cold Weather StartupEngine Maintenance Storage Routine MaintenanceFault Codes Troubleshooting GuidelinesProgrammable Controller Flash Engine Code Fault Shutdown Corrective Action Fault CodesTesting the Hydraulic Circuit Testing & TroubleshootingGeneral Problem Cause Remedy TroubleshootingEmissions SpecificationsFilters AccessoriesGTR20 Honda GTR20 Briggs Illustration QTY Description GTR20 Briggs Parts ListGTR20 Honda Engine Assembly QTY Description GTR20 Honda Parts ListFrame Parts Style Tank and CAP with NEW Style Tank and CAP Fuel Tank & CAPHOSES, Fittings & Clamps Main Wiring Harness Dual Circuit Wire Harness

GTR20 specifications

The Stanley Black & Decker GTR20 is a versatile and robust tool designed for professionals and DIY enthusiasts alike. Engineered with cutting-edge technology, the GTR20 stands out in the realm of power tools, particularly for those requiring precision and reliability in their projects.

One of the key features of the GTR20 is its powerful motor, which delivers exceptional torque and performance across various applications. This motor enhances the tool's capacity to handle tough materials, making it ideal for both heavy-duty construction tasks and intricate home improvement projects. The ergonomic design adds to user comfort, allowing for extended usage without causing fatigue.

Another significant characteristic of the GTR20 is its advanced battery technology. Equipped with a high-capacity lithium-ion battery, the GTR20 ensures long run times and quick recharge capabilities. This means that users can work for extended periods without the need for constant interruptions, greatly enhancing productivity on the job site. The battery life indicator is a thoughtful addition, providing users with real-time feedback on battery status, thus preventing unexpected shutdowns.

The GTR20 also boasts a sophisticated electronic speed control system, which allows users to adjust the speed according to different materials and tasks. This feature provides greater versatility, enabling more efficient cutting, drilling, or fastening. The tool's variable speed settings cater to various applications, making it a preferred choice for multiple trade professionals.

Durability is another hallmark of the GTR20. Constructed with high-quality materials and designed to withstand demanding conditions, this tool is built to last. The robust casing protects internal components from debris and damage, ensuring longevity even in the toughest environments.

Safety features are also paramount in the GTR20's design. The integrated safety lock and anti-slip grip contribute to user safety, minimizing the risk of accidents during operation. These attributes are essential for maintaining control and ensuring a secure hold, particularly in challenging projects.

Additionally, the GTR20 is compatible with a range of accessories, broadening its functionality. Users can switch between various bits and attachments, allowing for seamless transitions from one task to another.

In summary, the Stanley Black & Decker GTR20 is a high-performance tool that combines power, efficiency, and user-centric design. With its robust motor, advanced battery technology, electronic speed control, and durability, it appeals to a wide audience while meeting the demands of rigorous work environments. Whether tackling professional jobs or embarking on personal projects, the GTR20 is a reliable companion that delivers impressive results every time.
Top Page Image Contents