Shindaiwa manual Installing a Trimmer Head T272X, Install the Trimmer Head

Page 7

Installing a Trimmer Head T272

Retaining

Plug

Holder

Output shaft

Figure 9

Install the Trimmer Head.

1.Turn the trimmer over so that the gearcase output shaft faces UP.

2.Remove and discard the black plastic protective cap from the output shaft. See Figure 9.

3.Rotate the holder until the hole in the holder aligns with the notch on the gearcase. Use the long end of the hex wrench to lock the holder and output shaft. See Figure 10.

Hex Wrench

Figure 10

4.While holding the hex wrench, thread the trimmer head onto the output shaft, turning counter-clockwise. Using hand pressure only, tighten the trimmer head firmly on the output shaft.

IMPORTANT!

The trimmer head has a left-hand thread. For removal turn the trimmer head clockwise.

WARNING!

A standard grass trim- mer with a loop handle should NEVER be operated with

blade-type attachments. For blade use the trimmer must be fitted with a bicycle-type handlebar or a barrier bar that is located in front of the operator to reduce the risk of the operator from coming in contact with the cutting attachment (per ANSI B175.3). When using

a blade, the unit must also be equipped with a harness or strap.

5.Remove the hex wrench.

6.Adjust the trimmer line length to reach no further than the line

cutter on the cutting attachment shield. Trim to the correct length if necessary.

The T272 should now be

completely assembled and ready for

use with a trimmer head.

Installing a Trimmer Head T272X

NOTE:

The T272X is shipped with Holder A, the blade re- tainer (safety clip), Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT-HAND thread. Remove it by turning CLOCKWISE!

1. With the gearcase output shaft facing

up, rotate the gearshaft and holder A

until the hole in holder A aligns with

the matching hole in the gearcase

flange, and then lock the holder to the

gearcase by inserting the long end of

the hex wrench through both holes.

See Figure 11-A.

2. Using the combination spark plug/

screwdriver wrench, remove the shaft

bolt, bolt guard, holder B and the safety

clip. (The bolt guard, shaft bolt and

safety clip are not used with a trimmer

A

Shaft Bolt

Bolt Guard(not used) (not used)

Holder B

Safety Clip

Holder A

(not used)

 

 

35007

Gearcase

Shaft

Figure 11

B

Hand-tighten Trimmer Head (counter-

clockwise to install)

 

 

35008

Hex Wrench

 

head). See Figure 11-A.

3.

Install Holder B on the gearcase shaft.

 

The splined hole on Holder B must

 

engage with the gearcase shaft.

4.

Using the hex wrench to secure Holder

 

A , install and hand-tighten the trimmer

 

head (counter-clockwise to install).

 

See Figure 11-B.

5.

Remove the hex wrench from the

 

gearcase and holder.

WARNING!

A standard grass trimmer unit with loop handle should NEVER be operated with blade-type attachments. For blade use, the trimmer must be fitted with a bicycle-type handlebar or barrier bar that is located in front of the operator to reduce the risk of the operator coming in contact with the cutting attachment. (Per ANSI B175.3). When us- ing a blade, the unit must also be equipped with a harness or strap.

The T272X should now be

completely assembled and ready for use with a trimmer head.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents T272 Trimmer T272X Trimmer Introduction ContentsBe Aware of the Working Environment Properly Equipped OperatorUse Good Judgment Product Description Safety LabelsAssembly and Adjustments Handle T272/T272X Specifications T272X/C272Prior to Assembly To Change Position of Line Cutter Adjusting Throttle Level Free Play T272/T272XInstall the Cutting Attachment Shield Line cutter can be positionedInstalling a Trimmer Head T272X Installing a Trimmer Head T272Install the Trimmer Head Install Holder B on the gearcase shaft. See Figure Assembly and Adjustments Installing a Blade T272XExamples of 501 mixing quantities Mixing FuelFilling the Fuel Tank Starting the EngineStopping the Engine Engine Idle AdjustmentWhen the Engine Starts Idle Speed AdjustmentT272 Check Unit ConditionShoulder Strap T272X Cutting Grass-Units Equipped with a Trimmer HeadShoulder Strap Using a Brushcutter Blade T272XBlade Thrust Brushcutter Handlebar10/15-Hour Maintenance General MaintenanceDaily Maintenance Hour MaintenanceEvery 135 hours of operation Reassemble the muffler in the reverse order of disassemblyMultiple-tooth Circular Blade Long Term StorageBlade Sharpening Shindaiwa Tornado BladeRemedy Troubleshooting GuideWhat To Check Possible CauseWhat To Check Possible Cause Remedy LÀÕ«ÌÞ Symptom Possible Cause RemedyThis Warranty is Administered by Page Notas POR Administrada ES Garantía Esta Diagnóstico Guía Potencia Baja Arranca No Motor El Ertenciav¡A d Discos de AfiladoPlazo Largo de Almacenamiento Múltiples Dientes de DiscosHoras-50 Cada Mantenimiento Horas-135 Cada MantenimientoSilenciador el limpie General Mantenimiento Horas 10/15 Cada MantenimientoHoras-10 Cada Mantenimiento Diario MantenimientoDisco de Rebote T272X/C272 disco un UsandoVerticales Cortes Desmalezadoras para ArnésArnés Nylon de Cabezal con Equipadas Máquinas Césped de CorteUnidad La De Condición La Verifique Ertenciav¡A Motor del Mínima Marcha de AjusteContinuacin motor del Arranque Motor el arranca CuandoCombustible de Tanque el Llenando Nota Motor del ArranqueCombustible de Mezcla Seguro temporalmente retirar necesario T272X Disco el Instale Ajustes y EnsamblajeT272 Nylon de Cabezal del Instalación T272X Nylon de Cabezal del InstalaciónAccesorio del Protector el Instale Corte deEnsamblar de Antes T272/T272X Mango Ajustes y EnsamblajeT272X/C272 Especificaciones Mango el Ajustar ParaSeguridad de Etiquetas Producto del DescripciónJuicio Buen Use Ertenciav¡A d Trabajo de Area del Alerta EstéAlerta Mantengase Seguridad de Generales InstruccionesSeguridad de Declaraciones IntroducciónCausar o lesiones frir-su De riesgo el Disminuya Shindaiwa Propietario/Operador Del Manual

T272, T272X specifications

The Shindaiwa T272 and T272X are advanced professional-grade trimmers renowned for their powerful performance and innovative technologies. Designed for landscape maintenance professionals and serious enthusiasts, these tools exemplify durability, efficiency, and user-friendly features, making them stand out in the crowded market of outdoor power equipment.

At the heart of both models is a robust 25.4cc two-stroke engine that delivers exceptional cutting power while maintaining low emissions, thanks to Shindaiwa's proprietary engine technology. This engine provides reliable, high torque for heavy-duty applications, allowing users to tackle dense vegetation and tough grass with ease. The T272 and T272X are engineered with a strong focus on performance, enabling users to work longer and more efficiently.

One of the most notable features of the T272 and T272X is their lightweight design. Weighing in at approximately 10.2 lbs, these trimmers are easy to maneuver and reduce fatigue during extended use. The ergonomic handle design combined with an adjustable shoulder strap enhances comfort and balance, ensuring that operators can work without discomfort even after prolonged periods.

The T272X model comes equipped with an advanced ignition system that ensures easy starting and improved fuel efficiency. This system significantly reduces the number of pulls required to start the engine and enhances overall operation reliability. Additionally, both models utilize Shindaiwa's unique air filtration system, which extends engine life by reducing the amount of debris and dust entering the engine compartment.

Both trimmers feature a dual-line bump feed head for efficient trimming, allowing users to release more line with just a tap on the ground. The T272's head is designed for convenience and quick line replacement, while the T272X utilizes a more rugged, professional-grade head that accommodates thicker lines for demanding tasks.

In summary, the Shindaiwa T272 and T272X trimmers offer a perfect blend of power, efficiency, and ease of use. Their advanced technologies, user-centric designs, and exceptional performance make them an ideal choice for professionals in the landscaping industry as well as homeowners looking for a reliable trimming solution. Whether you are maintaining a small garden or managing a large estate, these trimmers are built to meet your needs and exceed your expectations.
Top Page Image Contents