How to Connect the MC1201, Banana plug connection

How to Connect the MC1201

Banana plug connection:

Caution: The supplied AC Power Cord should not be

connected to the Rear Panel of the MC1201

Insert the banana plug into the hole at the top of the

Amplifier until after the Loudspeaker Connections

terminal. Tighten the top portion of the terminal post

have been made and the supplied protective

and the set screw to secure the banana plug in place.

Terminal Connections Cover has been installed.

Note: The use of Banana Plugs is for use in the United

Failure to observe this could result in Electric

States and Canada only.

Shock.

4. Connect the loudspeaker hookup cable to the output

1. For Remote Power Control, connect a power control

terminals that match the impedance of your loudspeak-

cable from the Control Center or Preamplifier Power

er, being careful to observe the correct polarities. Out-

Control Out to the MC1201 Power Control In.

put impedance connections of 2 ohms, 4 ohms and 8

2. Connect a cable from the Balanced Output of a McIn-

ohms are provided. If the impedance of your loud-

tosh Preamplifier or Control Center to the MC1201

speaker is in-between the available connections, use

Balanced Input.

the nearest lower impedance connection.

Note: An optional hookup is to use an unbalanced cable.

WARNING: Loudspeaker terminals are hazardous live

3. Prepare the Loudspeaker Hookup Cable that attach to

and present a risk of electric shock. For

the MC1201 Power Amplifier by choosing one of the

additional instruction on making

methods below:

Loudspeaker Connections contact your

Bare wire cable ends:

McIntosh Dealer or McIntosh Technical

Carefully remove sufficient insulation from the cable

Support.

ends, refer to figures 1,

5. Attach the supplied Terminal Connections Cover with

2 & 3. If the cable is

the four Philip Head Mounting Screws (10-32 x 1/2

stranded, carefully twist

inch) to the Rear Panel of the MC1201 Amplifier. Re-

the strands together as

fer to figure 7.

tightly as possible.

Note: There are six openings on the bottom edge of the

Note: If desired, the twisted ends can be tinned with

cover to allow for the Loudspeaker’s Cable to exit

solder to keep the strands together, or attach spade

the MC1201. The Rear Chassis Handle (“U”

lug and/or banana connector.

shaped) has tapped screw openings on both sides

Spade lug or prepared wire connection:

for securing the cover to the MC1201.

Insert the spade lug

6. Connect the MC1201 power cord to an active AC out-

let.

connector or pre-

pared section of the

cable end into the

terminal side access

hole, and tighten the terminal

cap until the cable is firmly

clamped into the terminal so

the wires cannot slip out. Re-

Terminal

fer to figures 4, 5 & 6.

Connections

Cover

Rear

Chassis

Handle

Cover

Mounting

Screw

Locations

Cable Openings

Figure 7

MC1201 specifications

The McIntosh MC1201 is a high-performance monaural amplifier that exemplifies the brand’s commitment to delivering exceptional audio quality and performance. Known for its robust build and advanced technology, the MC1201 is designed to impress audiophiles and music professionals alike.

At the core of the MC1201 is a power output of 1,200 watts, allowing it to effortlessly drive even the most demanding speakers. The amplifier features McIntosh’s renowned Autoformer technology, which ensures that the full power is available regardless of the speaker's impedance. This technology helps in maintaining sound quality and performance across various load conditions, making the MC1201 versatile for different audio setups.

One of the standout characteristics of the MC1201 is its unique Circuit Design, including the use of McIntosh's exclusive Power Guard system. This innovative technology monitors the output to prevent distortion, safeguarding both the amplifier and connected speakers from damage during high-volume playback. This feature is especially beneficial for those who push their audio systems to the limits, providing peace of mind without sacrificing sound quality.

The MC1201 also incorporates the company’s proprietary Sentry Monitor, a protection circuit that ensures the amplifier operates safely under all conditions. If the output current exceeds safe levels, the Sentry Monitor will engage and temporarily reduce power output, allowing the amplifier to cool down and return to normal operation.

In addition to its powerful performance, the MC1201 boasts an aesthetically pleasing design. It features a sleek black glass front panel, illuminated meters that provide a visual representation of the audio output, and the iconic McIntosh logo, which signifies quality and luxury. The high-quality build ensures longevity and reliability, essential for both home audio enthusiasts and professional settings.

With its combination of power, advanced technology, and meticulous craftsmanship, the McIntosh MC1201 remains a sought-after choice for those seeking top-tier amplification solutions. Whether used in a home theater system or a high-fidelity audio setup, the MC1201 delivers an unparalleled listening experience, exemplifying McIntosh’s dedication to excellence in audio engineering.