Operation

Continuous operation is not recommended. If the amplifiers will not be auditioned for a few hours it is best to turn them off. This avoids undue stress to the KT88 output tubes.

As with all high fidelity products, the sound characteristics of the VAC amplifiers change somewhat as they warm up. Best sound will be achieved after 15 minutes of operation, with subtle changes occurring for up to one hour. However, we advise against leaving the equipment on at all times because of the attendant acceleration of output tube wear. Life of the output tubes averages between 2,000 and 8,000 hours depending upon brand fitted and random variations within the tubes themselves.

Any time that the VAC Power Amplifier has not been used for a few weeks the sound may be different. This is also normal for high resolution audio equipment. Optimum sound should return after a few hours of operation, preferably with an audio signal.

Please note that although your VAC amplifiers have been run for 48 hours at the factory, they will continue to "break in" for approximately 150 hours. Also be aware that many components display the need for a new break in period after being transported in unheated cargo aircraft.

Bias Adjustment

Your VAC Power Amplifier has been shipped with output tube bias preset. This should be checked when you install your amplifier, and periodically thereafter. It must also be set whenever an output tube is changed.

Adjustment of the output tubes is quite easy, and requires only a small screwdriver. On the front panel are four bi-color LEDs, each with an adjacent adjustment control. View the LEDs from directly in front, not from above or below. Adjust the LEDs to be green when the amplifier is not playing music. To set, turn the control clockwise until the LED just begins to change to an amber/red color, and then back the control off just slightly to restore the pure green color.

As music plays, the LEDs will vary from green to red. Check the bias if you ever see an LED stay red while music is not playing, or if an LED does not tend toward amber or red when music is playing. If the flashing of the LEDs is bothersome while listening, the switch on the front labelled “Bias Test” can be set to “0", disabling the LEDs. The switch must then be set to “1" to check the bias of the output tubes.

Any tube that can not be adjusted to the correct bias point should be replaced. Any tube which requires constant readjustment should be replaced immediately. Never operate the amplifier with an LED that shows red when music is not playing.

When installing new tubes, set the bias controls counter-clockwise. Check the bias of both channels as the amplifier warms up - don't wait ten minutes.

Bias levels should be checked monthly to ensure optimum sound quality. It is not unusual for the bias to change with time, particularly when tubes are new. The greatest amount of drift occurs during the first 200 hours of a tube's life. The drift may change direction periodically, such that the bias control must be increased and later decreased, or vice versa. Check bias if the sound seems lacking in detail or dynamics.

Tube Types

The input/splitter tube and the driver tube may be type 12AU7A/ECC82/E82CC or type 12BH7 (typically richer sound). The output tubes are type KT88. Please feel free to contact VAC if you require additional information or advice.

VAC PA100/100 specifications

The Mazda VAC PA100/100 is a pioneering innovation in the realm of automotive engineering, specifically designed to enhance driving dynamics and ensure optimal performance. This cutting-edge vehicle is recognized for its unique blend of advanced technologies and outstanding characteristics, making it a standout in the competitive landscape of modern automobiles.

One of the main features of the Mazda VAC PA100/100 is its lightweight construction. Utilizing high-strength materials, the vehicle achieves a remarkable balance between durability and weight reduction. This significantly improves fuel efficiency and enhances the overall handling of the car, allowing it to respond swiftly to driver inputs.

Powering the Mazda VAC PA100/100 is a state-of-the-art engine that combines efficiency with power. The engine employs a turbocharging system, maximizing performance while minimizing fuel consumption. This technology allows drivers to experience exhilarating acceleration without compromising environmental responsibility. With reduced emissions and enhanced mileage, the Mazda VAC PA100/100 demonstrates Mazda's commitment to sustainable driving.

The vehicle is also equipped with an advanced suspension system that optimizes ride comfort and handling. This system adapts to various driving conditions, ensuring stability and control regardless of the terrain. Drivers can expect a smooth ride with minimal body roll, which promotes confidence on tight corners and rough roads alike.

In terms of technology, the Mazda VAC PA100/100 features an intuitive infotainment system that integrates seamlessly with smartphones and other devices. This connectivity allows drivers to access navigation, music, and communication functions with ease. Additionally, the vehicle incorporates advanced safety features, such as adaptive cruise control, blind-spot monitoring, and automatic emergency braking, ensuring the utmost safety for both driver and passengers.

Moreover, the Mazda VAC PA100/100 boasts an ergonomic interior design that prioritizes comfort and usability. Quality materials and modern aesthetics create an inviting cabin environment, where every detail has been thoughtfully designed to enhance the driving experience.

In summary, the Mazda VAC PA100/100 is a remarkable vehicle that combines innovative technologies, exceptional performance, and a commitment to sustainability. With its lightweight structure, powerful engine, advanced suspension, and cutting-edge safety and infotainment features, it sets a new standard in the automotive industry, offering drivers an unparalleled driving experience that is both enjoyable and responsible.