Meridian America Meridian DSP, DSP Loudspeaker manual Tightening the drive units

Page 20

SETTING UP THE DSP

LOUDSPEAKERS

Caution (DSP6000 and DSP6000C only)

Meridian Audio has taken every care in the design, assembly, finishing and packing of this product. The high gloss finish on parts of the cabinet is achieved by painting up to five coats of polyester lacquer onto the plywood, each one hand polished.

Due to the product size and high technology cabinet construction, small marks on the lacquer surface may be visible when unpacked. These small marks can usually be removed as described in Cleaning, page 40.

It is the nature of all lacquer finishes to shrink over time. This is unavoidable and may result in cabinet joint lines becoming visible.

Meridian Audio has supplied products using lacquer finishes for many years and we are confident that when carefully used your product will return a lifetimeÕs enjoyment.

Tightening the drive units

The DSP loudspeakers typically take about two weeks of normal use for the drive units to settle. It is therefore recommended that you tighten the mounting bolts on each drive unit every few days during this period. Tighten the bolts in symmetrically opposite pairs using the 3mm hex wrench supplied.

Note (DSP5500): The DSP5500 grille frame has been designed to be as acoustically transparent as possible, and is quite fragile. When removing the grille, ease it carefully off by hand from the bottom and sides, avoiding excessive bending of the frame.

You should then check and if necessary retighten the drive units every few years.

To fit the feet (except DSP5000C and DSP5500HC)

The feet ensure that the loudspeakers have a stable base, and can be adjusted to allow for uneven floors. Use the spikes for carpeted floors; they are designed to penetrate the pile without damaging or flattening the carpet.

Each DSP loudspeaker needs four feet, fitted as follows:

¥Fit a lock nut to each spike, leaving about 2mm of thread between the lock nut and spike. If a foot is required rather than a spike, fit a foot cap. Screw each foot into the threads on the bottom of the base units. Do not fully tighten the foot at this stage.

15

Page 19 Page 21
Image 20
Page 19 Page 21
Contents R I D I a N D S P L O U D S P E a K E R E R G U I D E Meridian DSP Loudspeaker User Guide CD Radio LP TV Tape 1 Tape 2 CDR Cable DVD VCR 1 VCR 2 LDSales and service in the UK Sales and service in the USA Copyright and acknowledgementsContents Troubleshooting Introduction DSP loudspeaker drivers Digital Signal ProcessingMeridian DSP loudspeakers Power amplifiers Meridian High Resolution MHRCabinet Mounting optionsMeridian Comms Meridian Digital Music System Sample configurationsMeridian Digital Theatre Specification DSP5000 DSP5000C Power ControlSpecification DSP5500 DSP5500HC, and DSP5500C Characteristics Specification DSP6000 DSP6000C Characteristics Available accessories Setting up the DSP loudspeakers Components Care when unpackingUnpacking Tightening the drive units To fit the feet except DSP5000C and DSP5500HCTo dismantle the loudspeakers DSP6000 or DSP6000C only To install the head units DSP6000 or DSP6000C onlyTo fit the rubber bumpons DSP5000C and DSP5500HC only Radio interference Safety warnings Positioning the digital loudspeakersTo avoid overheating To obtain the best soundConnecting the loudspeakers Back panelDigital connections Communications connectionsTo use a DSP loudspeaker as a centre speaker Connecting to other equipmentTo connect two DSP loudspeakers in a Meridian system DSP loudspeaker Centre master CD Player Using the DSP loudspeakers To select a source Selecting a sourceRadio Status indicators Changing the displayRadio PCM 96k To change the displayed informationAdjusting the volume To change the volumeTo restore the sound To mute attenuate the soundChanging the treble, bass, or phase Phase +Tre.+0.0 Bass+0.0Changing the listening position BalAxis To change the balanceConfiguring the DSP loudspeakers Choosing standard settings TypeTo choose master or slave SlvTo specify the speaker position 500 Auto Bal. Y Centre N Diag. N To configure the DSP loudspeakerSpecifying information about your system RD Radio Configuring the sourcesTo configure a source FF. Y Configuring the setup options SetupFree Free Boundary Sub.1 Sub.2 CornerTo adjust the centre frequency response and tilt offset To store the settingsFre Tilt+1Troubleshooting Unit goes silent when played hard and displays ‘Hot‘ Display on front panel not litRemote not working There is radio interferenceDrive units move when the speaker is switched on or off Configuring the DSP loudspeaker does not have any effectUnit stays in standby Only the master loudspeaker playsCleaning Cleaning DSP6000 and DSP6000C onlyGuarantee Service and guaranteeService Troubleshooting Index Comms InputVolume Speaker positioning

DSP Loudspeaker, Meridian DSP specifications

The Meridian America Meridian DSP Loudspeaker represents a sophisticated blend of cutting-edge technology and audio excellence, tailored for audiophiles who demand nothing less than the best in sound reproduction. As a flagship offering from Meridian, a pioneer in high-performance audio systems, these loudspeakers are designed to deliver a captivating audio experience that immerses listeners in their favorite music, movies, and more.

One of the defining features of the Meridian DSP Loudspeaker is its digital signal processing capabilities. The integration of DSP technology allows for precise control over sound, optimizing audio playback for a variety of listening environments. This means that regardless of the room's acoustic characteristics, the loudspeaker can adapt its output to ensure that sound quality remains consistent and true to the original recording.

The Meridian DSP Loudspeaker boasts an impressive frequency response, enabling it to reproduce a wide range of audio frequencies with remarkable clarity. This capability is further enhanced by advanced driver technology, which includes custom-designed woofers and tweeters that work in unison to produce an articulate and dynamic soundstage. The result is a listening experience that captures the full emotional depth and nuance of music and film soundtracks.

Additionally, the loudspeaker's build quality is exceptional, featuring a robust cabinet design that minimizes resonance and distortion. This attention to physical construction ensures that the speaker performs optimally, preserving audio fidelity at all volume levels. The aesthetic appeal of the Meridian DSP Loudspeaker is also noteworthy, with a sleek and modern design that fits seamlessly into any home décor.

Connectivity options are versatile, allowing users to integrate the loudspeaker into a variety of audio systems effortlessly. With options for both wired and wireless connections, the Meridian DSP Loudspeaker can be easily paired with other audio components or used standalone, making it an adaptable addition to any setup.

Another remarkable characteristic of the Meridian DSP Loudspeaker is its ability to support high-resolution audio formats. This capability ensures that users can enjoy their music in the highest quality possible, making each listening session a truly immersive experience. The inclusion of proprietary technologies, such as Meridian’s Apodising filters, further enhances audio clarity and detail, ensuring that even the most complex musical passages are rendered with precision.

In summary, the Meridian America Meridian DSP Loudspeaker sets a high standard in the world of audio equipment. With its advanced DSP technology, exceptional sound performance, robust build quality, and versatile connectivity, this loudspeaker is ideal for those who seek to elevate their audio experience. Whether for music, movies, or any other form of entertainment, the Meridian DSP Loudspeaker promises to deliver an unparalleled sound journey for discerning listeners.
Top Page Image Contents