MTD 462 thru 464 warranty Setting Up Your Chipper Shredder, Loose Parts In Carton

Page 6
Setting Up

3

Setting Up

Your Chipper

Shredder

IMPORTANT

This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operat- ing your machine.

�

Figure 1 � Loose Parts In Carton

�Attaching The Hopper

Figure 1

�

Attaching The Chute DeflectorManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background�Manual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background

Figure 2

IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine.

Loose Parts In Carton

a.

Hopper Assembly

d. Bag

b.

Chute Deflector

e. Safety Glasses

c.

Chipper Chute

f. Engine Oil

Attaching The Hopper

Assembly

1.a. Remove six hex nuts and washers from the weld studs on the impeller housing. Do not remove the support plate. See Figure 1.

b.Place hopper assembly into position in front of impeller housing, aligning holes in hopper assembly collar with weld studs.

c.Slide hopper assembly onto weld studs and replace washers and hex nuts. Do not tighten completely.

2.a. Lift hopper assembly up to impeller bracket assembly.

b.Slide the release rod out slightly to hook the hopper bracket onto the rod. See Figure 2.

c.Tighten the six hex nuts that secure hopper assembly to impeller housing and also tighten the hex nuts that secure hopper bracket to hopper assembly.

Attaching The Chute Deflector

3.a. Remove the wing knobs from each side of the lower impeller housing.

b.Remove the hex lock nut, spacers, and hex bolt from the top of the impeller housing. See Figure 3.

4.a. Align the chute deflector in position on the discharge opening and insert hex bolt with spacer through hinge on chute deflector (spacers fit inside of hinges). See Figure 4.

NOTE: All references in this manual to the left or right side of the chip- per shredder is from the operating position only. Exceptions, if any, will be specified.

�

�

Manual backgroundManual backgroundManual background �

�

Figure 3

� Manual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background �

�

Figure 4

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents OPERATOR’S MANUAL Chipper Shredder - Model Series 462 thruMTD LLC, P.O. BOX 361131 CLEVELAND, OHIO Customer Support Table of ContentsFinding and Recording Model Number Model NumberSafety Labels Your ResponsibilityHEED ITS WARNING Training Safe OperationPractices PreparationOperation Maintenance & StorageSafe Operation Practices Do not modify engineLoose Parts In Carton Setting Up Your Chipper ShredderAttaching The Hopper Assembly Attaching The Chute DeflectorAttaching The Chipper Chute Attaching The BagOperating Your Chipper Shredder Know Your Chipper ShredderTow Bar If Equipped WARNING Never run the engine OperatingYour Chipper Shredder ide, an odorless and deadly gasLubrication Maintaining Your Chipper ShredderGeneral Recommendations Engine CareSharpening Or Replacing The Shredder Blade Storing Your Chipper ShredderCause Trouble ShootingProblem RemedyFor parts and/or accessories please call Model Series 462 Thru Parts List † Model Series 464 †† Model 464G Only Pop Rivet Page Page MANUFACTURER’S LIMITED WARRANTY FOR
Top Page Image Contents