MTD 60-1620-4 owner manual Setup Adjustments

Page 6

3

Setup and

Adjustments

WARNING

Disconnect and ground the spark plug wire as instruct- ed in the separate engine manual.

A

B

Figure 3-1

Figure 3-2

NOTE: The units illustrated may vary slightly from your unit.

1.Remove any packing material which may be between upper and lower handles.

a.Pull up and back on the upper handle to raise the handle from position A into the operating position. See Figure 3-1.

b.Tighten hand knobs securing upper handle to lower handle. Make sure that each carriage bolt is seated properly in the handle.

2.Place one carriage bolt (found in the hardware pack included with your unit) in the upper hole of the right handle mounting bracket from the inside outward. See Figure 3-2. Secure with one wing nut. Repeat process on the left side.

3.Rope guide Setup as follows, see Figure 3-3:

a.Hold the blade control against the upper handle. Position A.

b.Slowly pull starter rope out of engine. Position B.

c.Slip starter rope into the rope guide. Position C.

d.Tighten rope guide wing nut .Position D.

4.Insert post on cable tie into hole provided on the lower handle. Pull cable tie tight and trim excess. See Figure 3-4.

5.Each wheel has a height adjustment lever to change the cutting height of the mower. To change the height of cut, squeeze adjuster lever toward the wheel, moving up or down to selected height. See Figure 3-5.

IMPORTANT This unit is shipped

WITHOUT GASOLINE or OIL. After assem- bly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit.

A

B

D

C

Figure 3-3

Figure 3-4

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents For Assistance Call Table of Contents Finding and Recording the Model NumberCustomer Support Slope Gauge Your Responsibility General OperationSlope Operation Service General ServiceChildren Setup Adjustments Adjustments Operating Your Lawn Mower Know Your Lawn MowerStopping Engine Using Your Lawn MowerStarting Engine Operating TipsMaintenance Rear Flap Replacement Off-Season StorageBlade Mounting Torque Trouble Shooting Problem Cause RemedyYear Limited Warranty WarrantyVolet de départ manuel Wheel TreadsParts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Owner Responsibilities EZ Start Promise Provisions of Your Limited WarrantyItems and Conditions Not Covered General ConditionsFor parts and/or accessories refer to customer support on Page Garantie la par couvertes non conditions et Pièces Général d’ordre ConditionsPropriétaire du Responsabilités » EZ démarrage de Promesse La « Promise Start EZGarantie Propriétaire du l’intention àSolution Cause Problème DépannageEntretien Coupe de Plateau Lame la de remplacement et EntretienGénéral d’ordre Recommandations MoteurUtilisation ’essence et d’huile leins Option en déchiquetage de Bouchon’essence plein le jamais faites Ne Coupe de hauteur la de réglage de LeviersRéglages et Montage deInstructions Réglages et montage de Instructions Général Entretien EnfantPente une sur Utilisation Général en UtilisationInclinomètre ArbreClientèle la à Service Modèle de numéro du enregistrement et RepérageMatières des Table ’UTILISATION Guide

60-1620-4 specifications

The MTD 60-1620-4 is a robust and versatile outdoor power equipment machine designed for those who seek efficient and reliable lawn care. Known for its durability and performance, the MTD 60-1620-4 has become a preferred choice for both homeowners and professionals alike. This machine is part of MTD's extensive lineup of lawn care products, offering a blend of advanced features and technologies that enhance usability and efficiency.

One of the main features of the MTD 60-1620-4 is its powerful engine, which delivers strong performance under various conditions. This machine is equipped with a high-torque motor that ensures optimal cutting power, enabling it to tackle tough grasses and overgrown lawns without straining. Additionally, the engine is designed with fuel efficiency in mind, offering a balance between power and economy.

The MTD 60-1620-4 integrates cutting-edge technologies such as advanced deck design and precision cutting blades. The innovative deck geometry allows for improved airflow, which results in a cleaner cut and reduced clumping, while the high-quality blades are designed for longevity and sharpness. This combination ensures that the operator experiences minimal downtime, allowing for more efficient mowing sessions.

Another noteworthy characteristic of the MTD 60-1620-4 is its user-friendly controls and ergonomic design. The machine features adjustable handles, allowing users to find a comfortable operating position, which is particularly helpful for long mowing sessions. The intuitive control layout ensures that operators can easily access various functions without distraction, enhancing safety and comfort during use.

In addition to its functional features, the MTD 60-1620-4 is built with rugged materials that withstand the rigors of outdoor use. The frame is constructed from heavy-duty steel, providing stability and durability over time. Moreover, the machine's wheels are designed for a smooth roll over any terrain, making it suitable for various lawn types.

Maintenance of the MTD 60-1620-4 is simplified due to its accessible components, allowing users to conduct routine checks and adjustments with ease. This focus on user maintenance means that owners can keep their machine in optimal working condition with minimal hassle.

In summary, the MTD 60-1620-4 combines power, efficiency, and user-friendly design, making it an excellent choice for anyone looking to maintain a pristine lawn. Whether for residential use or professional landscape maintenance, this machine's advanced features and robust construction ensure it stands out in the competitive lawn care equipment market.
Top Page Image Contents