MTD 60-1616-6 owner manual Maintenance

Page 10

5

Maintenance

WARNING

Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

We do not recommend the use of pressure washers or garden hose to clean your unit. These may cause damage to electrical components, spindles, pulleys, bearings, or the engine. The use of water will result in shortened life and reduce serviceability.

Lubricate these points before reassembl

Figure 10

General Recommendations

1.Always observe safety rules when performing any maintenance.

2.The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the lawn mower as instructed here.

3.Changing of engine-governed speed will void engine warranty.

4.All adjustments should be checked at least once each season.

5.Periodically check all fasteners and make sure these are tight.

Lubrication

1.Lubricate the pivot points on the blade control handle at least once a season with light oil. The blade control must operate freely in both directions. See Figure 10.

2.If your mower is equipped with ball bearing wheels, lubricate at least once a season with a light oil, all other types require no lubrication. However, if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light automotive oil.

3.Lubricate the torsion spring and pivot point periodi- cally with light oil to prevent rust. See Figure 10.

4.Follow the accompanying engine manual for lubrica- tion schedule and instruction.

Engine

1.Refer to the separate engine manual for engine maintenance instructions.

2.Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully.

3.Under normal conditions service air cleaner as instructed in the separate engine manual packed with your unit. Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air cleaner should be serviced.

4.The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recom- mended at the start of each mowing season; check engine manual for correct plug type and gap specifica- tions.

NOTE: This spark ignition system meets all require- ments of the Canadian Interference-Causing Equipment Regulations.

5.Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air circulation which is essential to engine performance and life. Be certain to remove all grass, dirt and combustible debris from muffler area.

Deck

The underside of the mower deck should be cleaned after each use to prevent a buildup of grass clippings, leaves, dirt or other matter. If this debris is allowed to accumulate, it will invite rust and corrosion, and may prevent proper mulching.

The deck may be cleaned by tilting the mower and scrap- ing clean with a suitable tool (make certain the spark plug wire is disconnected).

Blade Care

WARNING: When removing the cutting blade for sharpening or replacement, protect your hands with a pair of heavy gloves or use a heavy rag to hold the blade.

Periodically inspect the blade adapter for cracks, especial- ly if you strike a foreign object. Replace when necessary. Follow the steps below for blade service:

1.Disconnect spark plug wire from spark plug.

2.Tip mower as specified in separate engine manual. If it does not specify turn mower on its side making sure that the air filter and the carburetor are up.

3.Remove the bolt and the blade bell support which hold the blade and the blade adapter to the engine crankshaft. See Figure 11.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents For Assistance Call Finding and Recording the Model Number Table of ContentsCustomer Support Slope Gauge General Operation Your ResponsibilitySlope Operation General Service ServiceChildren Manual Setup AdjustmentsThis unit is shipped Instructed in the separate engineSlowly pull starter rope out of engine. Position B Operating Your Lawn Mower Know Your Lawn MowerTo Stop Engine Using Your Lawn MowerOperating Tips Maintenance Tighten the hex bolt to the torque listed below Off-Season StorageRemove blade and adapter from the crankshaft Blade Mounting TorqueTrouble Shooting Problem Cause RemedyYear Limited Warranty WarrantyOHV Parts List Adressez-vous au «Service après-vente»Owner Responsibilities EZ Start Promise Provisions of Your Limited WarrantyItems and Conditions Not Covered General ConditionsFor parts and/or accessories refer to customer support on For parts and/or accessories refer to customer support on Propriétaire du Responsabilités Général d’ordre ConditionsGarantie la par couvertes non conditions et Pièces Garantie Propriétaire du l’intention àSolution Cause Problème Dépannage’utilisateur EntretienSaison hors Entreposage Avertissement Utilisation Commandes Figure la Voir .corde la de guide du Installation Guide le dans démarreur du corde la Glissez .cDoivent inférieur guidon La de instructionsRelative position Les RemarqueSécurité de Consignes Responsabilité Votre Inclinomètre ArbreModèle de numéro du enregistrement et Repérage Clientèle la à ServiceMatières des Table ’UTILISATION Guide

60-1616-6 specifications

The MTD 60-1616-6 is a highly versatile compact utility tractor that has gained recognition for its efficiency, durability, and user-friendly features. Designed primarily for residential and light commercial use, this machine is often used for tasks such as mowing, tilling, and landscaping.

One of the standout features of the MTD 60-1616-6 is its powerful engine. It is equipped with a reliable 16 horsepower engine that provides sufficient power for various attachments and implements. This engine is designed for easy starting and smooth operation, ensuring minimal downtime during critical tasks.

The tractor boasts a robust transmission system that allows for smooth and responsive gear shifts. With a choice of multiple speed options, users can customize their performance based on individual needs and terrain types. This flexibility is essential for users who may need to switch between high-speed travel and low-speed tasks like tilling.

Another notable characteristic of the MTD 60-1616-6 is its compact design. The tractor is specifically engineered to be maneuverable in tighter spaces, making it ideal for residential gardens and landscapes. Its smaller size does not sacrifice performance, making it a practical choice for homeowners with various outdoor projects.

The MTD 60-1616-6 is also compatible with a range of attachments, enhancing its functionality. From front-end loaders and tow-behind trailers to tillers and finish mowers, users can easily adapt the tractor for specific tasks. This adaptability allows for exceptional productivity, whether the user is clearing snow in winter or maintaining a garden in summer.

Comfort features are another important aspect of the MTD 60-1616-6. The tractor is designed with an ergonomic seat and adjustable controls, ensuring that operators can work for extended periods with minimal fatigue. Additionally, the tractor’s intuitive control layout makes it easy for both novice and experienced users to operate.

In terms of maintenance, the MTD 60-1616-6 is engineered for ease of access to key components. The design allows for straightforward maintenance tasks, ensuring longevity and reliable performance over time.

In conclusion, the MTD 60-1616-6 is a feature-rich compact utility tractor that combines power, versatility, and user comfort. Its reliable engine, smooth transmission, compatibility with various attachments, and thoughtful design make it a popular choice for homeowners and light commercial users alike.
Top Page Image Contents