MTD 260 Series warranty Maintenance, Lubrication, Engine, Deck, Blade Care

Page 10

5

Maintenance

WARNING

Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

We do not recommend the use of pressure washers or garden hose to clean your unit. These may cause damage to electrical components, spindles, pulleys, bearings, or the engine. The use of water will result in shortened life and reduce serviceability.

Figure 5-1

Lubrication

1.Lubricate the pivot points on the blade control handle at least once a season with light oil. The blade control must operate freely in both directions. See Figure 5-1.

2.If your mower is equipped with ball bearing wheels, lubricate at least once a season with a light oil, all other types require no lubrication. However, if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light automotive oil.

3.Lubricate the torsion springs and pivot point on the rear door periodically with light oil to prevent rust. See Figure 5-1.

4.The transmission is pre-lubricated and sealed at the factory and does not require lubrication.

5.Follow the accompanying engine manual for lubrica- tion schedule and instruction.

Engine

1.Refer to the separate engine manual for engine maintenance instructions.

2.Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully.

3.Under normal conditions service air cleaner as in- structed in the separate engine manual packed with your unit. Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air cleaner should be serviced.

4.The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each mowing season; check engine manual for correct plug type and gap specifications.

NOTE: This spark ignition system meets all require- ments of the Canadian Interference-Causing Equipment Regulations.

5.Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air circulation which is essential to engine performance and life. Be certain to remove all grass, dirt and combustible debris from muffler area.

Deck

The underside of the mower deck should be cleaned after each use to prevent a buildup of grass clippings, leaves, dirt or other matter. If this debris is allowed to accumulate, it will invite rust and corrosion, and may prevent proper mulching.

The deck may be cleaned by tilting the mower and scrap- ing clean with a suitable tool (make certain the spark plug wire is disconnected).

Blade Care

WARNING: When removing the cutting blade for sharpening or replacement, protect your hands with a pair of heavy gloves or use a heavy rag to hold the blade.

Periodically inspect the blade adapter for cracks, especial- ly if you strike a foreign object. Replace when necessary. Follow the steps below for blade service:

1.Disconnect spark plug wire from spark plug.

2.Tip mower on its side making sure that the air filter and the carburetor are up.

3.Remove the bolt and the blade bell support which hold the blade and the blade adapter to the engine crankshaft. See Figure 5-2.

4.Remove blade and adapter from the crankshaft.

5.The blade may be resharpened by removing it and either grinding or filing the cutting edge keeping as close to the original bevel as possible. Do not attempt to sharpen the blade while it is still on the mower.

6.It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade.

NOTE: Improper blade balance will result in excessive vibration causing eventual damage to the engine and mower. Be sure to carefully balance blade after sharpen- ing. Possible damage resulting from blade unbalance condition is not the responsibility of the manufacturer.

NOTE: Always remove blade from the adapter for testing balance.

7.The blade can be tested for balance by balancing it on a round shaft screwdriver. Remove metal from the heavy side until it balances evenly.

8.Before reassembling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner surface of the blade adapter with light oil.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents OPERATOR’S Manual Self-Propelled Mower Model SeriesFinding and Recording Model Number Table of ContentsCustomer Support Slope Gauge General Operation Your ResponsibilitySlope Operation General Service ServiceChildren This unit is shipped Setup AdjustmentsAinstructed in the separate engine manual Pull the chute deflector up towards engineDischarge of the grass Mower may be raised higher to allow betterOperation Know Your Lawn MowerStopping Engine Using Your Lawn MowerStarting Engine Operating TipsEngine MaintenanceLubrication DeckTighten the hex bolt to the torque listed below Belt CareOff-Season Storage Blade Mounting TorqueTrouble Shooting Problem Cause RemedyWarranty TWO Year Limited WarrantyModel 26M Adressez-vous au «Service après-vente» Parts List Pièces DétachéesFor parts and/or accessories refer to customer support on La page 2 pour ce qui concerne les pièces et/ou accessoiresGarantie ANS Deux DE Limitée GarantieSolution Cause Problème DépannageSaison hors Remisage Entretien’utilisateur Vilebrequin, le sur lame la de l’adaptateur PlacezMoteur LubrificationRéglages et Utilisation’entraînement de Position Position .moteur’assemblage, Après La de instructionsPleins les faites Est machine CetteGénéral Entretien EnfantPente une sur Utilisation Responsabilité VotreGénéral en Utilisation Inclinomètre ArbreModèle de numéro le trouver Pour Vente-après ServiceVente après service au d’abord adresser vous sans Matières des Table’UTILISATION Notice Important 260 Séries motrice-auto rotative Tondeuse

260 Series specifications

The MTD 260 Series is a highly regarded line of outdoor power equipment, known for its durability, versatility, and efficiency. Designed to cater to both residential and commercial users, the 260 Series has carved a niche for itself in a competitive market. Its range of products includes lawn mowers, string trimmers, and other essential gardening tools, each equipped with innovative features that enhance functionality.

At the heart of the MTD 260 Series is its robust engine technology. The series features high-performance engines that deliver reliable power and efficiency. Many models are equipped with easy-start systems, allowing users to start their equipment with minimal effort. This feature is particularly advantageous for those who may struggle with traditional recoil-start engines. The engines are designed to meet or exceed emissions standards, making them environmentally friendly without sacrificing power.

One of the standout characteristics of the MTD 260 Series is its ergonomic design. The handles are adjustable and cushioned, ensuring maximum comfort during extended use. This focus on user comfort extends to the lightweight design of many units, making them easy to maneuver even in tight spaces. Additionally, models in this series often feature compact designs that make storage convenient and hassle-free.

The cutting technology in the MTD 260 Series is another area where it excels. The lawn mowers, for instance, feature advanced blade systems that provide a clean and precise cut, ensuring a manicured lawn. Many models offer multiple cutting heights, allowing users to customize the length of their grass according to their preferences. Furthermore, the innovative grass collection systems efficiently gather clippings, reducing the need for additional cleanup.

Versatility is a key attribute of the MTD 260 Series. Many of its products are designed to accommodate attachments, expanding their functionality. Users can easily switch between mowing, trimming, and edging tasks, making the 260 Series a reliable choice for those with diverse outdoor maintenance needs.

In summary, the MTD 260 Series stands out for its powerful engines, ergonomic design, advanced cutting technology, and versatility. These features make it an excellent choice for homeowners and professionals alike, ensuring reliable performance and ease of use. The combination of durability and innovative technology positions the MTD 260 Series as a leading option in the outdoor power equipment market. Whether for routine lawn care or more challenging outdoor tasks, users can trust the MTD 260 Series to deliver exceptional results.
Top Page Image Contents