MTD 540-580 Series warranty Setup Adjustments, Tighten rope guide wing nut star knobs.Position D

Page 6

3

Setup and

Adjustments

WARNING

Disconnect and ground the spark plug wire as instruct- ed in the separate engine manual.

IMPORTANT This unit is shipped

WITHOUT GASOLINE

�

�

Figure 1

�

�

Figure 2

NOTE: The units illustrated may vary slightly from your unit.

1.Remove loose parts and any packing material which may be between upper and lower handles.

a.Pull up and back on the upper handle to raise the handle from position A into the operating position B. See Figure 1.

b.Tighten hand knobs (star knobs) securing upper handle to lower handle. Make sure that each carriage bolt is seated properly in the handle.

NOTE: On some models wing nuts have been replaced with star knobs. Figures show wing nuts only.

2.Locate hairpin clip in one hole on the weld pin on each side of lower handle.

a.Remove hairpin clip from this hole. Using a pair of pliers, insert hairpin clip into the other hole on the weld pin. Repeat on other side.

b.Place one carriage bolt (found in the hardware pack included with your unit) in the upper hole of the right handle mounting bracket from the inside outward. See Figure 2. Secure with one wing nut (star knobs). Repeat process on the left side.

3.Rope guide Setup as follows, see Figure 3:

a.Hold the blade control against the upper handle. Position A.

b.Slowly pull starter rope out of engine. Position B.

c.Slip starter rope into the rope guide. Position C.

d.Tighten rope guide wing nut (star knobs).Position D.

4.Insert post on cable ties into holes provided on the lower handle. Pull cable tie tight and trim excess. See Figure 4.

or OIL. After assem- bly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit.

�

� � �

Figure 3

Figure 4

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Rotary Mower Model Series 772C0836 04/13/06Table of Contents Finding and Recording Model NumberCustomer Support Slope Gauge Your Responsibility General OperationSlope Operation Service General ServiceChildren Setup Adjustments Tighten rope guide wing nut star knobs.Position DTo remove grass catcher and utilize the mulching feature To assemble the grasscatcherAttaching Grass Catcher to Mower Operating Your Lawn Mower Know Your Lawn MowerTo Stop Engine Using Your Lawn MowerSide discharge is an optional feature Operating TipsMaintenance Rear Flap Replacement Off-Season StorageBlade Mounting Torque Trouble Shooting Problem Cause RemedyWarranty TWO Year Limited WarrantyPage Parts List Pièces Détachées Adressez-vous au «Service après-vente»La page 2 pour ce qui concerne les pièces et/ou accessoires Client du disposition GarantieSituation ComSolution Cause Problème Dépannage’utilisateur Arrière déflecteur du RemplacementEntretien Lame la de montage de CoupleCoupe Lame la de remplacement et EntretienMoteur EfficaceUtilisation Commandes Faites NeMoteur le démarrer faire de Avant Sac le sur repose qu’il pour clapet le Lâchez CôtéTondeuse la de l’arrière La de instructions Responsabilité Votre EnfantGénéral Entretien Pente une sur Utilisation Reproduction la à liés problèmes d’autresCette Inclinomètre Vente-après Service Modèle de numéro le trouver PourMatières des Table ’UTILISATION Notice Important 580-540 Séries Rotative Tondeuse po

540-580 Series specifications

The MTD 540-580 Series represents a significant advancement in the realm of outdoor power equipment, offering versatile and efficient solutions for both homeowners and professionals. This series is designed to meet a variety of landscaping and lawn care needs, providing a powerful and reliable performance that stands out in the market.

One of the notable features of the MTD 540-580 Series is its robust engine options. These machines are equipped with high-performance engines that deliver consistent power and torque, enabling users to tackle tough cutting conditions with ease. The engines are designed for fuel efficiency, ensuring longer run times and reduced emissions, aligning with modern environmental standards.

The cutting technology in the 540-580 Series is another highlight, featuring advanced mowing decks that provide a clean and precise cut. The durable steel construction of the mowing decks enhances longevity, while the innovative blade design improves grass lift and cutting efficiency. With adjustable cutting heights, users can customize their mowing experience, ensuring optimal results for various grass types and conditions.

User comfort and ease of operation are prioritized in this series, with ergonomically designed handles and intuitive controls. These features ensure that even novice users can easily manage the equipment, reducing fatigue during extended use. Many models in the series also include features such as automatic or self-propelled capabilities, which further simplify the mowing process.

The MTD 540-580 models offer excellent maneuverability, thanks to their compact design and tight turning radius. This makes it easier to navigate around obstacles and fit into smaller spaces, making them ideal for residential lawns as well as commercial applications. The durability of these machines is fortified by high-quality components, which ensure reliability in demanding conditions.

In addition, the MTD 540-580 Series supports various attachments and accessories, enhancing its versatility. Users can equip their machines with leaf bags, mulching kits, and other accessories to cater to different lawn care tasks, making it a multifunctional tool that can adapt to seasonal changes and diverse landscaping needs.

Overall, the MTD 540-580 Series combines power, precision, and user-friendly features, making it a top choice for those seeking dependable outdoor equipment. Its commitment to innovation and performance positions it as a leader in the competitive market of lawn care machinery. Whether for personal or professional use, this series provides the tools necessary for achieving exceptional landscaping results.
Top Page Image Contents