MTD 022 Attaching Chute Deflector, Securing Brake Cable, Attaching Wheels, Attaching Starter Rope

Page 9

 

• Block the mower securely.

 

• Using hardware from group 1 of the hardware pack,

 

place axle bolt through the wheel with the hub side

 

of the wheel facing the deck. See Figure 8.

 

• Place the small bell washer on the axle bolt with the

 

crown side towards the wheel. See Figure 8.

 

• Secure the wheel to the deck with the large bell

 

washer and the nut.

Z Fitting

• Repeat on other sides.

 

• Remove blocks and put the mower on ground.

Figure 6

Attaching Chute Deflector

Securing Brake Cable

WARNING: The cable must be routed properly to avoid contact with all sharp edges and hot surfaces. Such contacts damage the cable and render the controls inoperative.

•Secure the cable to the lower left handle near the base of the unit with a cable tie from group 3 of the hardware pack. Trim off extra length of the cable tie. See Figure 7.

Lower Handle

Cable Tie

Figure 7

Attaching Wheels

NOTE: The holes provide three cutting heights for your mower. Use the same hole location for all four wheels when assembling. For example, if wheels are to be assembled in the lowest cutting position, use the highest hole on the deck.

 

Hex

 

Nut

Axle Bolt

Large

Wheel

Washer

Deck

Small

 

Washer

•Align the holes on the chute deflector with the corresponding holes on the deck.

•Using group 5 from hardware pack, place carriage bolts from underside of the deck and up through the chute deflector. See Figure 9.

•Secure each bolt with a washer and lock nut.

Chute

Lock Nut

Deflector

Washer

 

Carriage Bolt

 

Figure 9

Attaching Starter Rope

•Loosely attach the rope guide (from group 6 of the hardware pack) to the upper handle and thread the lock nut (also in group 6) only a few turns. Do not tighten. Make sure that the rope guide is to the outside of the upper handle. See Figure 10.

•The starter rope is attached to the engine. With the spark plug wire disconnected and grounded, depress the blade control handle and pull the rope out of the engine.

•Slip the starter rope through the gap between the rope guide and the handle. Tighten hex lock nut.

Starter

Rope

Rope

Hex

Lock

Guide

Nut

Figure 8

Figure 10

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesService Slope OperationChildren Your Responsibility MAY not Operate Safely Slope GaugeDisconnect Spark Plug Wire Attaching Lower Handle Assembling Your Lawn MowerTools Required Attaching Brake Cable Attaching Upper HandleAttaching Blade Control Handle Attaching Z FittingSecuring Brake Cable Attaching Chute DeflectorAttaching Wheels Attaching Starter RopeOperating Your Lawn Mower Maintaining Your Lawn Mower Blade Care Replacing Rear FlapEngine OFF-SEASON Storage Trouble Shooting GuideParts List for Model Series Model Series MANUFACTURER’S Limited Warranty for

022, 021 specifications

MTD 021 and 022 represent two significant models within the landscape of modern technology, primarily geared towards enhancing efficiency, connectivity, and user experience. Both models are designed to meet the evolving needs of consumers and businesses alike, focusing on innovative features and advanced technologies.

One of the standout features of the MTD 021 is its high-performance processor, which ensures seamless multitasking and rapid data processing. This is complemented by an impressive RAM capacity, allowing users to engage in demanding applications without any noticeable lag. The MTD 022, while also equipped with a robust processor, takes this a step further with its enhanced graphics performance, making it ideal for tasks involving multimedia content, gaming, or graphic design.

Connectivity is another area where both models excel. MTD 021 and 022 come equipped with a range of connectivity options, including Bluetooth 5.0 and Wi-Fi 6 capabilities. These technologies allow for faster data transfer rates and improved reliability, essential for today’s interconnected environments. Users can enjoy uninterrupted streaming and quick file sharing, making them suitable for both professional and personal use.

Battery life is a critical characteristic for any portable device, and both the MTD 021 and 022 impress with their energy efficiency. With advanced battery management technologies, users can expect longer usage times between charges. This feature is crucial for those on the go, eliminating the need for frequent recharging and enhancing overall productivity.

In terms of design, the MTD 021 and 022 emphasize sleek, modern aesthetics. The lightweight frames and durable materials used in construction ensure portability while maintaining a premium feel. Both models are ergonomically designed for comfortable handling, which is beneficial during extended use.

Security features in MTD 021 and 022 are state-of-the-art, incorporating biometric verification systems such as fingerprint readers and facial recognition technology. This ensures that sensitive data remains protected, appealing to users who prioritize privacy and security in their devices.

In conclusion, MTD 021 and 022 are trailblazers in their category, characterized by their powerful performance, advanced connectivity options, impressive battery life, stylish design, and robust security features. As technology continues to advance, these models stand out as excellent choices for users looking to enhance their digital experience.
Top Page Image Contents