Remote Control Unit RC4200PM

a. MAIN POWER ON button

Turns the PM4200's power on when it is in the stand-by mode.

b. MAIN POWER OFF button

Sets the PM4200's power to the stand-by mode when it is set to the power-on mode.

c. SOURCE POWER button

Switching the mode of a CD player, tuner, CD-R or other Marantz component equipped with a power stand-by function between power-on and stand-by is enabled by pressing this button after the FUNCTION SELECT button corresponding to the component has been pressed.

When this button is pressed after pressing the TUNER button, the tuner's power is turned on; when it is pressed again, the tuner is set to the stand-by mode.

When this button is pressed after pressing the AMP button, the PM4200 is switched from the power-on mode to the stand-by mode or vice versa.

SYSTEM REMOTE CONTROLLER RC4200PM

	The RC4200PM can be used to control a Marantz AV component
	equipped with a remote sensor as well as other Marantz compo-
	nents connected to the first component through the Remote
	Control Bus. The buttons of the RC4200PM are laid out on its
	control panel according to the functional groups as described
English	below.	z					x
English			MAIN POWER SOURCE
			ON	OFF	POWER	AMP
			PHONO	CD	TUNER CD-R
			AUX	DVD	TAPE	MD
			1	2	3	ÅF/P	v
			4	5	6	ı- / --
			7	8	9	MODE
			–	0	+	MEMO
					z–MODE–x
			SCROLL CANCEL TEXT			TIME
						MUTE

					OPEN/	VOLUME	c
					CLOSE	VOLUME	c

zPOWER ON/OFF buttons

xFUNCTION SELECT button

PHONO button : When this button is pushed the input of

PHONO is selected.

CD button : When this button is pushed the input of CD is selected.

TUNER button : When this button is pushed the input of

TUNER is selected.

CD-Rbutton : When this button is pushed the input of CD-R is selected.

AUX button : When this button is pushed the input of

AUX/DVD is selected.

DVD button : When this button is pushed the input of

AUX/DVD is selected.

TAPE button : When this button is pushed the input of MD/TAPE is selected.

MD button : When this button is pushed the input of MD/TAPE is selected.

cVOLUME UP/DOWN button

UP button : VOLUME knob turns when this button is pushed and the volume level is grows.

DOWN button : VOLUME knob turns when this button is pushed and the volume level is falls.

vMUTE button

When this button is pushed, the sound is not temporarily emitted from the speakers.

When this button is pushed again, MUTE is released. Moreover, when up/down of the volume is operated by remote control, MUTE is released.

Other buttons are not applied to PM4200.

Please see at the owners manual of other equipment’s about the operation of button.

USING THE REMOTE CONTROL UNIT

1. Remote control

Operate the remote control unit within a distance of approx. 5 m from the infrared signal reception window (remote sensor) on the front of the Amplifier.

Remote control operation may not be possible if the remote control unit's transmitter is not pointing in the direction of the remote sensor or if there is an obstruction between the transmitteote sensor.

Remote control operating range

Amplifier

Approx. 5 m

60°

Remote control unit

2. Loading batteries

Batteries in this remote control unit have a life of approximately 1 year under normal operating conditions. When the remote control unit is not to be used for an extended period of time, remove the batteries. Also, when you notice that the batteries are starting to run down, replace them as soon as possible.

(1)Remove the battery cover.

Remote control unit

Rear side

(2)Insert batteries with correct + / – orientation.

Two AA (R6)-size batteries

(3)Close the battery cover until it clicks shut.