Microsoft SHG-TS, SHG-TC, SHG-VS, SHG-A* Absolute Mounting the Scale, Double End Mounting

Page 5

Mounting the Scale

4.0MOUNTING THE SCALE

4.1Double End Mounting

Note:

Refer to section 4.3 for mounting scales in excess of 2.5 metres.

Each end of the scale is different and can be identified by the “calibration adjustment end” and the “fixed end.

Figure 4.1 -Scale

NOTES:

(A)Erroneous readings will occur if the reader head is allowed to travel beyond the effective travel limits (Refer to Figure 4.1).

(B)The pre-load on the balls are factory set via the set screw at the calibration adjustment end. Caution: Do not tamper with or adjust the set screw as this will alter the calibration and accuracy specification of the scale and void the warranty (Refer to Figure 4.1).

(C)When mounting scales in the vertical plane, the calibration adjustment end should be positioned at the top.

Once the reader head is secured and correctly aligned, the scale support brackets can now be fitted. The scale support brackets consist of the support pin, the support link and the pillar(s).

Traverse the machine to its maximum position toward the non-cable entry side of the reader head. Maximum position means all available travel, including hand winding past any electrical limits or trip dogs.

Carefully slide the scale or setup tube through the reader head, allowing for a sufficient amount of scale to project from the reader head in order to fit the scale support brackets. Note: If the scale travel is more then 60" it is recommended that a setup tube is used for alignment to avoid accidental damage to the actual scale tube.

Assemble the scale support link to the scale support pin leaving approximately 3mm (1/8") gap between the bottom of the pin shoulder and the top of the link.

Slide the link/pin assembly onto the scale to approximately 5mm (0.2") away from the end of the reader head.

Transfer punch through the support link and into the machine casting. It is important that the support link is kept square to its mounting surface at all times.

Remove the link/pin assembly and the scale from the reader head. Drill and tap M8 x 18mm deep (USA 5/16 - 18 x 3/4" deep) into the machine casting as marked by the transfer punch. Fit the pillar(s) to the machine casting by using one of the methods shown in Figure 4 .3. The pillar should fit square and flush to the machine surface.

Newall Measurement Systems

4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents SHG-A* Absolute, SHG-TC, SHG-TS & SHG-VS Linear Encoders Contents Introduction IntroductionBracketry PreparationMounting the Reader Head Encoder AssemblyEncoder Assembly / Mounting the Reader Head Double End Mounting Mounting the ScaleMounting the Scale Reader head and bracket alignment Support pillars Single End MountingSingle end mounting Scales in Excess of 2.5 MetersLong scale support bracket assembly Mounting the Scale / Fitting the Scale Guard Fitting the Scale GuardCable Routing / Final Check Cable RoutingFinal Check Appendix a Appendix a Scale Bracket Mounting Options Outboard scale support mounting Scale supports invertedAppendix B Appendix B Dimensional Drawing Appendix B cont’d Appendix B Dimensional Drawing Newall Measurement Systems 023-80620/03-UK .Oct

SHG-A* Absolute, SHG-VS, SHG-TS, SHG-TC specifications

Microsoft's SHG product line includes the SHG-TC, SHG-TS, SHG-VS, and SHG-A* Absolute solutions, each designed to cater to varying user needs and preferences within the tech ecosystem. These products demonstrate Microsoft's commitment to innovation, performance, and reliability, making them relevant for consumers from casual users to business professionals.

The SHG-TC, or Turbo Charge model, emphasizes efficiency and performance. It boasts an advanced processing unit that optimizes power consumption while delivering maximum output, making it ideal for users who demand high performance without compromising battery life. This model is particularly suited for applications that require significant processing power, such as gaming and graphic design.

The SHG-TS, or Turbo Ultra, builds upon the foundation set by its predecessor with enhanced thermal management techniques. This feature allows users to maintain optimal performance levels even during extended use, minimizing overheating issues. With a focus on multitasking capabilities, the SHG-TS integrates a high-speed SSD and expanded RAM options, providing a swift and responsive experience for users who work with multiple applications simultaneously.

Next in the lineup is the SHG-VS, or Vision Series. This model focuses on visual quality and clarity, making it particularly appealing to designers, photographers, and video editors. Equipped with a high-resolution display and advanced graphics capabilities, the SHG-VS ensures that colors are vibrant and images are sharp. Furthermore, it supports a wide array of creative software, allowing professionals to execute their projects with precision and ease.

Finally, the SHG-A* Absolute serves as Microsoft's premium offering, combining the best features from previous models while incorporating cutting-edge technologies. This model prioritizes user experience with a sleek design, intuitive interface, and seamless integration with other Microsoft services and devices. It includes advanced security features, such as biometric authentication, ensuring that user data remains protected at all times.

In summary, the Microsoft SHG-TC, SHG-TS, SHG-VS, and SHG-A* Absolute represent a diverse range of technological advancements, catering to various user requirements. Each model combines performance, efficiency, and innovative features, positioning Microsoft as a leader in the modern tech landscape. With their commitment to quality and user satisfaction, these products are well-suited for anyone looking to enhance their digital experience.
Top Page Image Contents