Vector VEC012B owner manual Charging Times, Amps, Care and Maintenance, Troubleshooting

Page 9

CHARGING TIMES

The Charger will automatically adjust the charge rate as the battery charges and stops charging when the battery is fully charged. If you require some estimate of the time it takes to charge a battery refer to the chart below.

PERCENT OF CHARGE

75%

50%

25%

0%

2 AMPS

7 HRS

13 HRS

NR*

NR*

4 AMPS

3.5 HRS

6 HRS

9 HRS

12 HRS

6 AMPS

2.5 HRS

5 HRS

7 HRS

9 HRS

* Not recommended.

The times shown in the chart above are approximate and refer to an average auto- motive battery. For smaller batteries, the charge time should be adjusted using the for- mula shown below and adding 1 hour to the time calculated. To estimate charging time for a discharged battery, divide the amp hour (AH) rating of the battery by the charge rate selected. This is the number of hours required to recharge the battery. For example, a 50 Ah (12 volt) battery is discharged (10 volts).

Question: How long should it be charged at the 6 Amp rate?

Divide the 50 Ah by 6.

Answer: Approximately 8 hours. Always round up charge time by 10% to ensure full charge. In most cases, battery charge times will vary depending on age and condi- tion of battery. Smaller batteries should be charged at the lower rate (2 Amps) and add an extra hour to charge time.

NOTE: Deep cycle batteries may need longer charging time. It is recommended to repeat the charging cycle a second time beginning with the 2 Amp rate.

CARE AND MAINTENANCE

With minimal maintenance, the Jump ‘n Charge system will provide years of depend- able service.

•After each use, clean the battery charger clamps - be sure to remove any battery fluid that will cause corrosion of the copper clamps.

•Clean the outside case of the charger with a soft cloth and, if necessary, mild soap solution.

•Do not use charger if cords or clamps have been damaged in any way - call Vector Technical Support Department toll-free: (866) 584-5504 for replacement cords/clamps.

TROUBLESHOOTING

NOTE: Charger will NOT operate on batteries below 4.0 volts. If a 12 volt battery is below 4.0 volts, it is probably shorted, open or sulfated. Replace the battery.

The following conditions may light the FAULT LED:

•Charging too fast - Decrease Charge Rate - Press 2/4/6 Amp pushbutton to select lower rate.

8

Page 8 Page 10
Image 9
Page 8 Page 10
Contents VEC012B Jump ‘n ChargeGeneral Battery Safety Important Safety InstructionsPersonal Precautions and Safety AC Power Cord Connection Introduction and FeaturesFeatures Battery Status Display Smart Battery ChargerDC Connection Precautions Preparing to ChargeCharger Location Charging the Battery Outside a Vehicle Charging the Battery in a VehicleOperation Charger Controls and IndicatorsTroubleshooting Care and MaintenanceCharging Times AmpsInternal Short Cell Battery Sulfated BatteryBattery not Accepting a Charge Very Cold BatteryCharger Controls and Indicators Alternator Check ProcedureReplacement Parts Prba Jump ‘N Charge Controls and IndicatorsSTEP-BY-STEP JUMP-STARTING Instructions Read and Observe ALL Cautions and WarningsOperation for DC Charging CHARGING/RECHARGINGOperation AS a 12 Volt DC Portable Power Supply Jump ’N Charge SpecificationsEmergency Area Light Year Limited Warranty Program

VEC012B specifications

The Vector VEC012B is a robust and versatile jump starter designed to provide reliable emergency power for a wide range of vehicles. This compact device stands out in the market with its impressive features, making it a favored choice for both casual users and automotive enthusiasts.

One of the key features of the VEC012B is its powerful Lithium-Ion battery. This advanced battery technology ensures a high energy density, enabling the jump starter to deliver a substantial amount of power while maintaining a lightweight profile. With a peak current of 1,500 amps, the VEC012B can easily jump-start vehicles with larger engines, including trucks and SUVs, making it suitable for various applications.

In addition to its jump-starting capabilities, the Vector VEC012B is equipped with multiple USB ports, allowing users to charge mobile devices, tablets, and other electronics on the go. This versatility is perfect for outdoor adventures, ensuring that users remain connected while on the road.

Safety is a top priority for the VEC012B, which comes with built-in protection features that prevent short circuits, overcharging, and reverse polarity connections. The clamp design is optimized for secure attachment to vehicle batteries, ensuring a safe and efficient jump-start experience.

The VEC012B also includes an integrated LED flashlight, providing added convenience during nighttime emergencies or in poorly lit conditions. The flashlight offers multiple modes, including a strobe function, which can be useful for signaling for assistance.

Durability is another strong point of the Vector VEC012B. Its rugged design is built to withstand harsh conditions, making it an ideal companion for off-road adventures or emergency situations. The compact size and included carry case enable easy transportation and storage, allowing users to keep the device handy in their vehicles without taking up much space.

Overall, the Vector VEC012B is an essential tool for anyone looking for a reliable jump starter. Its combination of high power output, multiple charging options, safety features, and portability makes it a standout product in the jump starter market, providing peace of mind for drivers everywhere. Whether for everyday use or emergency situations, the VEC012B is a must-have device for vehicle owners.
Top Page Image Contents