Land Pride AFM40200 Transport Hitch LUG, 804-027C Washer Lock Spring 1 PLT, Front P.T.O. Mount

Page 11

Section 2: Frame

Table of Contents Part Number Index

Transport Frame

Land Pride

Applies to AFM40200 (S/N 146999-)

Ref. Part No.

Part Description

Comments

Revision

dwg11951

Drawing Image Number

 

 

1. 315-004H

TRANSPORT HITCH LUG

Changed to three lug

 

2.890-182C SAFETY CHAIN 10000 LB

3.802-074C HHCS 1-8X6 1/2 GR5

4.804-027C WASHER LOCK SPRING 1 PLT

5.803-031C NUT HEX 1-8 PLT

6.804-029C WASHER FLAT 1 SAE PLT

7.890-118C SCREW JACK 2000#

8.315-105H TRANSPORT FRAME AFM40200

9.807-023C SPRING HOSE LOOP

10.802-014C HHCS 3/8-16X3/4 GR5

11.804-013C WASHER LOCK SPRING 3/8 PLT

12.804-012C WASHER FLAT 3/8 SAE PLT

13.802-075C HHCS 1-8X7 GR5

14.315-063H TRANSPORT LOCK - WING DECK

15.805-149C PIN HITCH 1 X 3 3/4 USABLE PLT

16.806-066C U-BOLT 1/2-13 X 3 1/32 X 4

17.803-020C NUT HEX 1/2-13 PLT

18.804-015C WASHER LOCK SPRING 1/2 PLT

19.315-115H REAR DECK HITCH LOCK BAR WELD

20.802-050C HHCS 5/8-11X1 1/4 GR5

21.803-021C NUT HEX 5/8-11 PLT

22.804-022C WASHER LOCK SPRING 5/8 PLT

23.315-227D REAR DECK HITCH LOCK BRACE

24.802-100C HHCS 5/8-11X4 1/2 GR5

25.315-313D REAR DECK LOCK PIN STORAGE

26.315-060H REAR DECK LOCK ROD

27.183-022D PRESS WHEEL TRUNNION-ADJUSTING

28. 315-226D TUBE 1 OD X 5/32 WL X 1 3/4

29.315-061H CENTER DECK CYLINDER MOUNT

30.315-311D REAR CYL MOUNT PIVOT PIN

31.802-152C HHCS 1/4-20X2 GR5

32.803-007C NUT LOCK 1/4-20 PLT

33. 814-100C TIRE & WHL ASSY 23 X 10.5-12

34.890-005C BUSHING CYL 1 1/4 X 1 X 1

35.804-021C WASHER FLAT 5/8 SAE PLT

36.803-024C NUT LOCK 5/8-11 PLT

37.

803-020C

NUT HEX 1/2-13 PLT

(S/N 98861+)

Rev. 2 not compat. w/Rev. 1

37.

803-014C

NUT HEX 3/8-16 PLT

(S/N 98860-)

Rev. 1

38.

804-015C

WASHER LOCK SPRING 1/2 PLT

(S/N 98861+)

Rev. 2 not compat. w/Rev. 1

38.

804-013C

WASHER LOCK SPRING 3/8 PLT

(S/N 98860-)

Rev. 1

39.

806-066C

U-BOLT 1/2-13 X 3 1/32 X 4

(S/N 98861+)

Rev. 2 not compat. w/Rev. 1

39.

806-021C

U-BOLT 3/8-16 X 3 1/32 X 4

(S/N 98860-)

Rev. 1

40.

315-004H

TRANSPORT HITCH LUG

 

Rev. 2

40.

315-065H

RPBY 315-004H

 

Rev. 1

41.

315-139H

FRONT P.T.O. MOUNT

(S/N 128483+)

 

42.

804-016C

WASHER FLAT 1/2 SAE PLT

(S/N 128483+)

 

43.

805-109C

PIN COTTER 1/8 X 1 1/4 PLT

(S/N 128483+)

 

44.

315-146E

AFM40200 TRANS SPINDLE LH SUB

 

 

45.

315-148E

AFM40200 TRANS SPINDLE RH SUB

 

 

11/06/07

AFM40200 (S/N 146999-) All-Flex Mower 315-486P

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents All-Flex Mower Table of Contents Alphabetized Table of Contents Table of Contents Part Number Index Table of Contents Part Number Index Center Deck Link 315-055H Center Deck Lift Link 315-312D Lift Link Pivot PIN 315-206D Rear Deck Adjuster Bolt12 -343D Rear Deck Height Adjust Wrench Right Hand and Left Hand Tool Bar 315-310D Toolbar Pivot PIN CYL 3X8X1.25 ROD TIE no PinsAFM R. H. Deck SUB AFM L. H. Deck SUBTransport Frame 11 -013C Washer Lock Spring 3/8 PLT Transport Hitch LUG804-027C Washer Lock Spring 1 PLT 807-023C Spring Hose LoopTransport Frame Tire and Hub 816-014C Tine Gauge Wheel HUB Seal 4P TM TL4P Trfchief Washer Flat 3/4 SAE PLTDriveline Arrangement PTO Shaft 35HP X 34 W/EXT Cone WAY BOX COVER/PTO GuardAFM14,16,22 GB W/HDWR Shipout 315-048S Bearing BASE/DRV SHFT/BRG AssyDriveline Assembly Center Shaft and Bearing 822-099C Flangette 72 MST Plated 315-062D Front PTO Guard315-005H Front PTO Cover & BRG Mount 804-013C Washer Lock Spring 3/8 PLTDriveline 826-100C Walterscheid WS Inboard Yoke Walterscheid Safety ChainWS Cross Bearing KIT Walterscheid Cross & BRG KITDriveline All Decks 826-012C Eurocardan S/N EC INNER/OUTER Tube Bearing EC Cross AssemblyEC Yoke Assembly TRACT. END Driveline with EXT. ConeDriveline All Decks 826-012C Walterscheid S/N WS Inner Profile Waltscheid Cross & BRG KITWalterscheid Inboard Yoke Walterscheid Spring PINDriveline All Decks 826-111C Walterscheid S/N 100497+ 387332 REP by 387266 054482 Driveline CV 826-089C 826-125C 826-101C Waltersheid WS Inboard Yoke W/BRIDGE WS Grease ZerkWS Double Yoke WS Cross & Bearing KITDriveline Slip Clutch 053314 Waltersheid WS Flanged Ring Walterscheid Clutch HousingWS Friction Clutch WS Snap RingBelt Drive MWR BLD 5/16 X 25SD LL CW 808-128C B-GROOVE Idler Pulley 6.25 ODIdler Spacer Washer Blade 2ODX.56THKX.51IDBelt Take-Up Handle 817-028C Double Disk ARM Pivot Bushings 804-022C Washer Lock Spring 5/8 PLTCW Belt TAKE-UP Handle Center Deck Blade Hub Center Grease Tube Blade HUBBlade Spindle W/KEY 1/4SQ X7/8 BearingCenter Deck Channel ITG 1-14 Slotted HEX NUT 817-050C Gearbox Shaft ProtectorGroove Pulley 11 CAST-IRON 16 -015C Washer Lock Spring 1/2 PLTDeck Clip U-TYPE NUT 1/4-20 SLF-RET 315-233D Deck Belt GuardWing Head Screw W/WEAR Washer Nylon PUSH-ON RetainerRight Hand and Left Hand Deck Blade Hub 12 -312D Lube Fitting 3 Extension 808-127C B-GROOVE Drive Pulley 6 O.DRight Hand and Left Hand Deck Channel Spring TAB 2 Hole Washer Lock Spring 1 PLTNUT HEX 1-8 Nylon Insert PLT NUT HEX 1-8 PLTCastered Gauge Wheel Spacer PIN Wire Retaining 1/4 X 1 3/4W Yoke SUB Assy GW Spacer 1/4Center Deck Gauge Wheel 12 -202C Gauge Wheel SFT Pivot Bushing Center Connect Link804-023C Washer Lock Spring 3/4 PLT Gauge Wheels 814-070C and 814-114C S/N RIM W/DRAIN Holes & Brgs -114C Tire 13X5.00-6 AIR Tire W/HOLESTilden BRG 1.38 OD X3.7LG.75ID Tilden Rtnr 3/4IDX1 3/8ODX1/4LNon-Castered Gauge Wheel 14 -097H Wing Rear GW Mount 315-095S AFM Rear GW NON-CASTEREDNON-CASTER GW Yoke Weld AIR TIREW/HOLESRight Hand and Left Hand Deck Gauge Wheel 10 -192D Gauge Wheel ARM Shim Plate 890-202C Gauge Wheel SFT Pivot Bushing315-102H Rear GW ARM Center Deck AFM Gauge Wheel ARM SUBGearbox 826-081C 826-085C ITG ITG Retaining Ring ITG Gearbox HousingBearing Ball ITG Input ShaftGearbox 4-Way Splitter 826-097C CO Shaft CO Adjustment SPACER, 35.3CO Cover CO GasketGearbox All Decks 826-121C Comer Comer Shim KIT Gearbox All Decks 826-121C ITG ITG Gasket ITG G-BOX HousingITG M18 Pipe Plug Vented ITG Input HUB CAPHydraulic Arrangement CA 1/2FNPT TE 3/4MJIC BH RUN TEEHydraulic Cylinder 810-005C Energy EGY Piston ROD Guide CYL 2X8X1.12 ROD Single ActingEGY Piston ROD Back UP Ring 2 O.D ROD WiperHydraulic Cylinder 810-138C Midway MW Tube PIN Hair Cotter .148 WireMW Clevis STD. Duty MW HeadHydraulic Cylinder 810-139C Midway TIE ROD NUT Midway MW RODHead Midway Hydraulic Cylinder 810-195C Midway Wiper Seal MW ROD 1-1/4 DIA X 8 StrokeMW Tube 3 X 8 Cylinder MW TIE ROD 3 X 8 CylinderLabel Placement PLATE-LAND Pride 10 -488C Decal PTO Maintenance CVDecal Flag 818-165C LP Logo Small Buckskin Safety Label Placement 17 -337C Decal Warning 20 MPH Trans SML Decal Caution Transp Lock DisePart Number Index 43, 47 Great Plains Manufacturing, Inc
Related manuals
Manual 114 pages 59.01 Kb

AFM40200 specifications

The Land Pride AFM40200 is a specialized mower designed for efficiency and performance in maintaining roadside areas and grasslands. Known for its durability and exceptional cutting capabilities, this mower is suited for both commercial landscaping tasks and agricultural applications.

One of the main features of the AFM40200 is its cutting width of 200 inches. This large cutting deck allows users to cover substantial areas quickly, making it an ideal choice for professionals who need to maintain expansive landscapes. The mower is equipped with a three-blade design that ensures a clean cut, promoting healthier grass and enhancing the aesthetic of the maintained areas.

The AFM40200 utilizes a fully welded frame construction, ensuring a sturdy and robust build that can withstand the rigors of frequent use. This durability is complemented by a heavy-gauge steel design, which contributes to the mower's ability to handle tough terrain and challenging weather conditions. The mower is designed for easy attachment to various tractors, with quick-connect hook-ups that streamline the setup process and reduce downtime.

Incorporating innovative technology, the AFM40200 features a rear discharge design that prevents grass clumping and allows for even distribution of clippings across the cutting area. This results in less maintenance and a tidier finish, which is particularly beneficial for clients focusing on aesthetics. The mower also boasts an adjustable cutting height, allowing operators to customize the cut to specific requirements, whether they are mowing for aesthetics or to promote healthy grass growth.

The Land Pride AFM40200 is also equipped with a unique suspension system, which enhances its stability and maneuverability on uneven terrain. This feature provides a smoother ride for operators and improves the overall cutting consistency. Furthermore, maintenance is simplified with accessible grease fittings and easily replaceable blades, making it convenient for operators to keep the mower in optimal condition.

Overall, the Land Pride AFM40200 stands out in the market due to its combination of size, durability, and advanced features. Whether for professional landscaping or agricultural upkeep, this mower offers a reliable solution for anyone needing to maintain large grassy areas efficiently and effectively. With its impressive specifications and user-friendly design, it is a valuable investment for those in the mowing industry.
Top Page Image Contents