Land Pride RCR16 Series manual Transporting, Cutting Instructions, Operating Check List

Page 14

Land Pride

Section 2 Operating Instructions

Transporting

!CAUTION

When traveling on public roads, use accessory lights and devices for adequate warning to operators of other vehicles. Comply with all federal, state and local laws.

IMPORTANT: Always disengage the tractor’s PTO before raising the cutter to transport position.

1.When raising the cutter to the transport position be sure that the driveline does not contact tractor or cutter.

2.Be sure to reduce tractor ground speed when turning; and leave enough clearance so the cutter does not contact obstacles such as buildings, trees or fences.

3.Limit transport speed to 20 mph. Transport only with a tractor of sufficient size and horsepower. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely.

4.When traveling over rough or hilly terrain, shift tractor to a lower gear.

!DANGER

To prevent personal injury caused by thrown objects, the use of front & rear safety guards is strongly recommended! To avoid injury or death from entanglement in rotating drivelines, the drive gearbox shields must be in place and secure when operating.

Cutting Instructions

1.Your cutter is equipped with free-swinging cutting blades to reduce shock loads to the cutter if striking obstacles.

2.Start the machine slowly; do not use full throttle. Allow 10 seconds for cutter blades to become aligned properly before going to full power.

3.The ground speed depends on two things: the density of the material being cut, and the size of the tractor. Never run fast enough to overload the tractor.

4.It is important to maintain correct RPM PTO speed. Loss of PTO speed will allow the blades to hinge back and result in ragged, uneven cutting.

5.This cutter was designed to cut grass and brush 1” maximum diameter.

Operating Check List

In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training involved in the operation, transport, maintenance and storage of equipment. Before beginning to cut, the following inspection should be performed.

!CAUTION

Damage may occur if exceeding the rated cutting capacity of the cutter!

!CAUTION

Do not overspeed PTO or machine damage may result. This cutter is designed to be used with tractors having a 540 RPM rear PTO. Know what your tractor specifications are.

Operating Checklist

Check

Reference

Read “Important Safety

page 1

Information” in this Manual.

 

 

 

Check oil level in gearboxes.

Section 3

 

Page 17

 

 

Check that all plugs in gearbox have

Section 3

been replaced properly.

Page 17

 

 

Be sure nuts and bolts are tight.

Section 1

 

 

Be certain all guards and shields are in

Section 1

place.

page 9

 

 

Lubricate the cutter as needed. Refer to

Section 3

“Maintenance and Lubrication”.

Page 17

 

 

Leveling Procedure

There are 5 primary adjustments that should be made prior to actual field operation:

1.Deck level from left to right

2.Tractor top link length

3.Tractor lower link height

4.Tailwheel height

5.Cutter slightly higher in the rear than the front.

12 RCR16 Series Rotary Cutters 312-742M

12/14/01

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Rotary Cutters Table of Contents Be Aware of Signal Words 911 Avoid High Pressure Fluids Hazard 818-543C Important Safety Information818-130C 818-540C818-564C 818-552C818-556C 818-142C818-830C Owner Assistance Using This ManualApplication IntroductionTractor Requirements Dealer AssemblyAssembly and Set-Up Optional Equipment Assemblies Driveline InstallationTorque Values Chart for Common Bolt Sizes Rear Chain GuardsFront Rubber Guards Rear Rubber GuardTractor Hook-Up Transporting Operating ChecklistLeveling Procedure Cutting InstructionsTractors have only a single adjusting crank Nominal Cutting HeightCutter Height Adjustment Driveline Clutch Optional MaintenanceService Cutting Blades Shearbolt DrivelineClutch Assembly and Disassembly StorageGauge Wheel Hub LubricationGauge Wheel Spindle Tube GearboxDriveline Profiles Driveline U-JointsDriveline Shield Bearings Specifications and Capacities TailwheelFeatures and Benefits Troubleshooting Problem Cause Solution Excessive vibration Torque Values Chart for Common Bolt Sizes AppendixWarranty Page Corporate Office P.O. Box Salina, Kansas 67402-5060 USA

RCR16 Series specifications

The Land Pride RCR16 Series represents a benchmark in the world of rotary cutters, specifically designed for those who demand efficiency, durability, and exceptional performance in land clearing and maintenance tasks. The RCR16 Series features a robust construction that ensures longevity and reliability, making it an ideal choice for both commercial and residential applications.

One of the standout features of the RCR16 Series is its heavy-duty design. The cutter is built with a reinforced frame that can withstand rigorous use, making it suitable for tackling thick brush and dense undergrowth. The cutter's durable materials ensure that it can endure the challenges posed by various terrains, allowing users to work effectively in diverse environments.

In terms of technology, the RCR16 Series employs a specially designed blade system that delivers superior cutting performance. The cutter is equipped with high-quality, heat-treated blades that maintain their sharpness over extended periods, reducing maintenance time and increasing cutting efficiency. The blade mounting system also allows for quick and easy adjustments, enhancing the overall user experience.

Another significant characteristic of the RCR16 Series is its versatility. The cutter comes in various sizes and configurations, making it adaptable to different tractors and uses. It can handle both tall grasses and heavy brush, providing users with the flexibility to manage their land according to their specific needs. Whether you are clearing a field or maintaining a roadside, the RCR16 Series rises to the occasion.

Safety features are paramount in the RCR16 Series, which includes a reinforced safety chain that protects against debris and unintended contact, ensuring a safer operation. Additionally, the cutter is designed with operators in mind, featuring easy-to-reach controls and a user-friendly design that minimizes operator fatigue during long hours of use.

Overall, the Land Pride RCR16 Series is a reliable and powerful tool that embodies quality and performance. Its heavy-duty construction, advanced cutting technologies, and versatile applications make it an exceptional choice for anyone looking to manage land effectively. Whether you are a professional landscaper or a dedicated landowner, the RCR16 Series promises to exceed expectations and provide years of dependable service.
Top Page Image Contents