King Kutter 999994 manual Attaching to Tractor

Page 17

ATTACHING TO TRACTOR continued....

STEP 5

Place and hold inner PTO shaft section next to outer section and check if PTO shaft is too long. Each section should end approximately 3 inches short of reaching u-joint shield on the opposite section. If the shaft is too long measure

3 inches back from each u-joint shield and mark the other shaft section. Be sure to do this for both PTO shaft halves. NOTE: Do not cut PTO shaft sections at this time.

STEP 6

Raise finishing mower and remove blocking. Raise and lower finishing mower in order to locate the longest distance between equipment input shaft and the trac- tor PTO output shaft. With the finishing mower in the longest distance position shut down the tractor and SECURELY BLOCK THE FINISHING MOWER IN POSITION.

STEP 7

As in step 5 hold PTO shaft sections together and check for a minimum of 6 inches of overlap. If PTO shaft has been marked for cutting the overlap is the distance measured between the two marks. If the PTO shaft has less than a 6 inch overlap, DO NOT USE. Contact your authorized King Kutter Dealer.

NOTE

If the PTO shaft length is too long go to SIZING PTO SHAFT (pg. 18)

STEP 8

Apply any multi-purpose grease to the outside of the male (inner) PTO shaft section. Assemble PTO shaft and install on finishing mower and tractor.

WARNING - Failure to install retaining clip on gearbox input shaft would allow driveline to swing freely if bolt is sheared causing possible injury or death.

STEP 9

Pull on tractor side of PTO shaft yoke to be sure it has locked in place. Make certain PTO shaft shielding is in place and good working condition.

STEP 10

The PTO shaft shield is a non-rotating design and must be secured prior to equipment use. Using the chain on each yoke shield attach to a fixed object on the tractor and equipment ends that will not allow the PTO shaft shield to rotate during operation.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Free Floating Rear Discharge Flex Hitch Finishing Mower Page To the Purchaser Page Contents Safety Equipment Safety Guidelines Fig. D Fully Assembled Finishing Mower Assembly Instructions StepFigure C Shipped with OIL in Gearbox Before Putting Finishing Mower Into ServiceSafety Training Prepartion Starting and Stopping SafetyOperational Safety Operational Safety Transport Safety Attaching to Tractor Attaching to Tractor Sizing PTO Shaft Step Operating Instructions Cutting Height AdjustmentFinishing Mower Operation Step Figure C MaintenanceTo Replace Belt To Adjust BeltFigure D FT. Finishing Mower only FT. Finishing Mower only Storage Safety Maintenance SafetySafety Sign Locations Page Page Page Page Page Model no Description SN# Rear Discharge Flex Hitch Finishing Mower Stainless HP Gearbox ’-5’-6’ Gearbox 22 PTO Blade Spindle Unit LA Magdalena BONDIOLI- BypyEurocardan Series Bondioli Cover Removal PTO Shafts Cover Removal Limited Warranty

999994 specifications

The King Kutter 999994 is a top-tier product in the realm of agricultural equipment, predominantly recognized for its heavy-duty construction and versatile performance. This rotary cutter has been engineered to meet the needs of both professional landscapers and farmers, offering an exceptional combination of durability and efficiency.

One of the most prominent features of the King Kutter 999994 is its robust build quality. Constructed from high-strength materials, this rotary cutter is designed to withstand the rigors of demanding tasks. The cutter deck is reinforced, providing added protection against impact and abrasion while enhancing the overall lifespan of the equipment. Its all-steel frame ensures stability and reliability, even in the toughest working conditions.

The King Kutter 999994 is equipped with a high-performance gear box that promotes optimal power transfer from the tractor to the blades. This effective transmission enables the cutter to handle thick brush and tall grass effortlessly. Additionally, it is powered by a reliable PTO (Power Take-Off) system, ensuring consistent performance across a range of tractor models.

Another key characteristic is the adjustable cutting height feature, which allows users to select the desired height for various types of grass and brush. This versatility makes the cutter suitable for a wide array of applications, from maintenance of large fields to landscaping around homes and commercial properties.

The blade design also sets the King Kutter 999994 apart. The blades are crafted from high-grade steel, featuring a special heat treatment that enhances cutting efficiency and reduces wear. With a sharp edge and aerodynamic design, these blades ensure a clean and efficient cut, contributing to improved lawn health and aesthetics.

Safety features are paramount in the design of the King Kutter 999994. The rotary cutter comes equipped with safety chain guards and a shielded design to help protect the operator from flying debris during operation. This attention to safety, combined with ease of use, makes it an excellent choice for individuals looking to tackle their land maintenance tasks confidently.

In conclusion, the King Kutter 999994 combines heavy-duty construction, advanced technology, and user-friendly features to create an exceptional rotary cutter capable of meeting various land clearing needs. Whether for commercial landscaping or rural property maintenance, this equipment stands out for its performance, reliability, and safety, making it a valuable asset for any agricultural operation.
Top Page Image Contents