KitchenAid LI3Y7C/W10322991C Installation Instructions, Electrical Requirements, Prepare Location

Page 6

For Non-Vented (recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the outside, the hood can be used in the non-vented (recirculating) version, using a Recirculation Kit (which includes charcoal filters and a deflector). To order, see the “Assistance or Service” section.

Roof Venting

Wall Venting

Non-vented

 

 

(recirculating)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

B

AA

B

B

A

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

 

required.

If the house has aluminum wiring, follow the procedure

 

below:

A. Roof cap

A. Wall cap

A. Deflector

B. 6" (15.2 cm)

B. 6" (15.2 cm)

B. 6" (15.2 cm)

round vent

round vent

round vent

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent Piece

6" (15.2 cm) Round

 

 

45° elbow

2.5 ft

 

(0.8 m)

90° elbow

5.0 ft

 

(1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example vent system

90 elbow

 

 

 

 

 

 

Wall cap

 

 

6 ft (1.8 m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2ft

(0.6 m)

The following example falls within the maximum recommended vent length of 35 ft (10.7 m).

1

- 90° elbow

= 5.0 ft (1.5 m)

1

- wall cap

= 0.0 ft (0.0 m)

8 ft (2.4 m) straight

= 8.0 ft (2.4 m)

 

 

Length of system

= 13.0 ft (3.9 m)

 

 

 

1.

Connect a section of solid copper wire to the pigtail

 

leads.

2.

Connect the aluminum wiring to the added section of

 

copper wire using special connectors and/or tools

 

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

INSTALLATION

INSTRUCTIONS

Prepare Location

It is recommended that the vent system be installed before hood is installed.

Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.

Check your ceiling height and the hood height maximum before you select your hood.

1.Disconnect power.

2.Determine which venting method to use: roof, wall, or non- vented.

6

Image 6
Contents Canopy Range Hood Range Hood Safety Table DES MatièresImportant Safety Instructions Installation Requirements Tools and PartsLocation Requirements Venting Requirements Installation Instructions Electrical RequirementsPrepare Location Vent Cover Support Bracket Installation Install Range HoodRange Hood Mounting Screws Installation Complete PreparationConnect Vent System For vented installations onlyFor non-vented recirculating installations only Make Electrical ConnectionInstall Vent Covers Complete InstallationOperating the light Range Hood USERange Hood Controls Operating the blowerRange Hood Care CleaningNon-Vented recirculating Installation Filters Exterior SurfacesWiring Diagram AGCU.S.A Assistance or ServiceAccessories CanadaKitchenaid Ventilation Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences Dinstallation Exigences d’emplacementOutils et pièces Exigences concernant l’évacuation Dimensions du placardInstallation dans une région à climat froid Air dappointDécharge par larrière Décharge à Installation sans Travers le toit Travers le murSpécifications électriques Calcul de la longueur effective du circuit dévacuationInstallation des vis de montage de la hotte Instructions DinstallationPréparation de lemplacement Installation de la bride de cache-conduitInstallation de la hotte Raccordement du circuit dévacuationInstallation des cache-conduits Raccordement électriqueUtilisation DE LA Hotte Achever l’installationCommandes de la hotte de cuisinière Utilisation de la lampeEntretien DE LA Hotte NettoyageSchéma DE Câblage OhmsAssistance OU Service AccessoiresAu Canada Garantie DU Système DE Ventilation Kitchenaid La présente garantie limitée ne couvre pasW10322991C All rights reserved

LI3Y7C/W10322991C specifications

The KitchenAid LI3Y7C/W10322991C is a versatile and innovative appliance that embodies modern kitchen technology and design. This model, known for its robust construction and sleek aesthetics, is a prime example of KitchenAid's dedication to blending functionality with elegance.

One of the standout features of the LI3Y7C is its advanced motor system, designed to provide exceptional power while maintaining quiet operation. This ensures that you can mix even the thickest batters without disturbing the pleasant ambiance of your kitchen. The motor's efficiency also translates into longer-lasting performance, making it a reliable companion for daily cooking tasks.

The LI3Y7C boasts a unique planetary mixing action. This technology rotates the bowl and the beater simultaneously, ensuring complete mixing coverage and eliminating the need for manual scraping. With multiple speed settings, users can easily adjust for different recipes, whether they're blending, kneading, or whipping.

A key characteristic of this model is its spacious mixing bowl, which allows for larger quantities of ingredients. Made from stainless steel, the bowl is not only durable but also easy to clean, making maintenance a breeze. The ergonomic handle provides a comfortable grip, enhancing usability during food preparation.

Another notable aspect is the versatility offered by the LI3Y7C, as it’s compatible with a wide array of KitchenAid attachments. From pasta makers to food grinders, these attachments expand the appliance's functionality, allowing it to perform multiple culinary tasks. This adaptability makes it an indispensable tool for both novice cooks and seasoned chefs.

Safety features are also prioritized in the design of the LI3Y7C. The appliance includes a built-in overload protection system, which prevents the motor from overheating during extended use. This not only ensures longevity but also offers peace of mind to users.

In terms of aesthetics, the KitchenAid LI3Y7C/W10322991C is available in various colors to suit different kitchen decors. Its timeless design and compact size allow it to fit seamlessly into any countertop space, enhancing the kitchen's overall look.

In summary, the KitchenAid LI3Y7C/W10322991C stands out for its powerful motor, advanced planetary mixing action, generous mixing bowl, and compatibility with a wide range of attachments. These features, combined with a focus on safety and design, make it an essential addition to any kitchen. Whether you're baking a cake, whipping cream, or preparing dough, this appliance delivers consistent results, helping you create delicious meals with ease.