Kettler 2548 manual Adirondack Rocking Bench, Assembly Instructions, Contents, Tools Required

2548 ADIRONDACK ROCKING BENCH

Contents:		(18) 1/4 - 20 x 2” Bolts
(1)	Seat, (1) Back	(6)	1/4 - 20 x 2 1/2” Bolts
(2) Arm Rests		(1)	#10 x 3” Screw
(2)	Front Chair legs	(10) Washers
(2)	Back Chair legs	(10) Locknuts
(2)	Cross Braces	Locknut Washer Bolt
(2)	Rocker Feet

Tools Required:

#3 Phillips Head Screwdriver

7/16” Wrench

a. Align predrilled holes then insert bolts

1.to attach front legs.

b. Align predrilled holes then insert bolts to attach back legs.

1a. 1b.

2.	Place arm rest
	on top of chair
	legs, align front		Attach the back
	predrilled holes,	3.
			of the chair by
	insert bolt.		aligning holes on

Assembly Instructions

1. a. With the wing on the post facing front,

align the predrilled holes on front leg to the seat

and insert the 1/4 - 20 x 2” Bolts through the leg

in thru the seat. Clean any plastic residue from the

bolt then slide a washer on. Screw on the locknut

and then tighten it with the wrench and phillips

screwdriver.

b. Align the predrilled holes on the back leg to

the seat and insert the 1/4 - 20 x 2” Bolts through

the leg in thru the seat. Clean any plastic residue

from the bolt then slide a washer on. Screw on the

locknut and then tighten it with the wrench and

phillips screwdriver. Repeat on the other front leg.

6.

the arm and the seat to insert bolt.

3b.

3a.

4.

Attach the braces to

the legs by5. aligning holes

and inserting a 2” bolt.

Attach the rocker to the legs by aligning holes to metal insert, use a 3” bolt.

Insert the bolt thru the center seat brace into the center of the back of bench.

2. Place arm rest on top of chair legs align the
front predrilled holes and insert the 1/4 - 20 x 2”
Bolts through the leg and in thru the arm. Clean
off any plastic residue then slide a washer on the
end of bolt. Screw on the locknut and then tighten
it with the wrench and phillips screwdriver.
3.	a. Attach the back of the chair to the seat
by aligning holes and inserting a 1/4 - 20 x 2”
Bolt then tighten with a phillips screwdriver.

b. Attach the back of the chair to the arm by aligning holes and inserting a 1/4 - 20 x 2 1/2” Bolt thru the arm, leg and into the chair back, then tighten with a phillips screwdriver.

Repeat on both sides.

4.Attach the cross braces of the chair to the legs by aligning holes and inserting a 1/4 - 20 x 2” Bolt through the leg into the cross brace and tighten with a phillips screwdriver.

Repeat on other leg.

Do Front and Back cross braces.

5.Attach the rocker for the chair. Align the predrilled hole on the rocker to the metal isert at the bottom of each leg and insert a 1/4 - 20 x 2 1/2” bolt then tighten with the screwdriver.

Bolt rocker to both front and back legs.

6. Attach the center seat brace underneath to the back, insert a #10 x 3” screw thru the brace into the center of the bottom back support then tighten with the screwdriver.

	Made in the U.S.A.
	www.kettlerusa.com
Copyright © Kettler USA 309.01	info@kettlerusa.com