Jonsered 2159 manual Start and Stop, Start and stop

Page 28

START AND STOP

Start and stop

WARNING!

•Never start the saw engine without the bar, chain and clutch cover (chain brake) assembled - or else the clutch can come loose and cause personal injuries.

•Always move the saw away from the fueling area before starting.

•Place the saw on clear ground and make sure that the chain is not contacting anything. Also, make sure that you have a secure footing.

•Keep people and animals well away from the working area.

WARNING!

The catalytic converter muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when handling the saw near flammable substances or vapours.

Start

Grip the front handle with your left hand and hold the saw down by putting your right foot in the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until the starter pawls engage. Then pull sharply.

Push in the choke control immediately when the engine ignites and make repeated starting attemps. When the engine starts, rapidly give full throttle. Then the throttle latch will disengage.

Cold engine

CHAIN BRAKE:

Disengage the chain brake by pulling the hand guard towards the front handle.

IGNITION; CHOKE:

Set the choke control in choke position. The stop contact will automatically be set to start position.

FAST IDLE:

Combined choke/fast idle is received when the choke is moved to choke position.

If the saw is fitted with a decompression valve (A): Press the valve to reduce the pressure in the cylinder and make starting easier. Always use the decompression valve when starting the saw. Once the saw has started the valve will automatically return to its original setting.

Warm engine

Use the same procedure as for starting cold engine but without choke. Fast idle is recived by first set the choke control in choke position, and then back again.

H

A

H

CAUTION! Do not release the starter handle from fully pulled out position as this can cause damage on the saw.

Stop

The engine is stopped by switching off the ignition.

28 – English

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Operator´s manual EPA KEY to Symbols SymbolsContents Safety Instructions Personal Protective EquipmentChain brake and front hand guard Chain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking brake band wear Checking the front hand guardChecking the inertia brake release Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesCutting equipment designed to minimise kickback BarSaw chain Some terms that describe the bar and chainSharpening your chain and adjusting raker clearance General information on sharpening cutting teethSharpening cutting teeth Risk of kickback is increased with a badly sharpened chainSetting the raker clearance General advice on setting raker clearanceTensioning the chain Lubricating cutting equipment Chain oilFilling with chain oil Never use waste oilNeedle bearing maintenance Checking chain lubricationChecking wear on cutting equipment Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Do not let go of the handles General rulesNever use the saw one- handed Min m 10 ftBasic safety rules General Working InstructionsBasic cutting technique GeneralTerms CuttingTree felling technique Safe distanceLimbing Felling directionClearing the trunk and preparing your retreat FellingGeneral advice Freeing a tree that has fallen badly = high accident riskCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? What is what?Assembly Mounting guide bar and chainFuel Handling FuelmixFuelling Chain oilMin 3 m 10ftStart and Stop Start and stopStart StopMaintenance CarburetorStarter device assembly Starter deviceChanging a broken or worn starter cord Tensioning the recoil springNeedle bearing maintenance Spark plug Air filterMuffler IMPORTANT! a damaged air filter must always be replacedAdjustment of the oil pump Heated handles 2159W Centrifugal cleaning TurboCooling system Electrically heated carburetor 2159WWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data 2159Emission Control Warranty Statement + 46 36 14 65108 87 2001W38
Top Page Image Contents