Marantz SR4600 manual Recalling a Preset Station, Preset Scan, Sorting Preset Stations

(Using the remote control unit)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the remote. “– –“ (preset number) starts blinking on the display.

3. Enter the desired preset number by pressing the numeric buttons.

Note:

•When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.

RECALLING A PRESET STATION

	1.	SET UP/		MENU OFF
		T.TONE
		PURE DIRECT	AUTO		DTS
	1.		1	2	3
EIVER SR4600		NIGHT	CSII	EX/ES	VIRTUAL
			4	5	6
		DISPLAY	MCH-ST	STEREO	7.1CH IN
			7	8	9
		CLEAR	MEMO	A/D	P.SCAN/V-OFF
	1.			0
				CHANNEL/SKIP
		BASS	TREBLE	TUNE/SEARCH
			T-MODE	RDS	F.DIRECT

PRESET SCAN

	SET UP/		MENU OFF
	T.TONE
	PURE DIRECT	AUTO		DTS
		1	2	3
	NIGHT	CSII	EX/ES	VIRTUAL
		4	5	6	1.
	DISPLAY	MCH-ST	STEREO	7.1CH IN
		7	0	9
3.	CLEAR	MEMO	A/D	P.SCAN/V-OFF	3.
			CHANNEL/SKIP
3.	BASS	TREBLE	TUNE/SEARCH
		T-MODE	RDS	F.DIRECT
	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY
	CH SEL			LIP SYNC

(Using the remote control unit)

1. Press the P.SCAN on the remote.

“PRESET SCAN” appears on the display and then the preset station with the lowest preset number is recalled first.

2. Preset stations are recalled in sequence (No.1

→No.2 → etc.) for 5 seconds each.

No stored preset number will be skipped.

3. You can fast forward the preset stations by pressing the ¢ continuously.

When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P.SCAN on the remote.

SORTING PRESET STATIONS

AV SURROUND RECEIVER SR4600

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

1)87.1 MHz

2)93.1 MHz

3)94.7 MHz

10)105.9 MHz

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5:

To sort the numbers, press and hold the MEMO and thecursor buttons.

“PRESET SORT” will appear on the display and sorting will be done.

1.	Recall the preset number to be inputted name
	with the method described in “Recalling” a
2.	preset station.
	Press the MEMO button on the front panel or
	press the MEMO button on the remote for
3.	more than 3 seconds.
	The left most column of the station name
	indicator flashes, indicating the character
4.	entry ready status.
	When you press the or cursor buttons on

the front panel or the 5 / 6 buttons on the remote, alphabetic and numeric characters will be displayed in the following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→ / → (Blank) → A

UP →

← DOWN

5. After selecting the first character to be entered,

press the MEMO or ENTER buttons, press the

MEMO button on the remote.

The entry in this column is fixed and the next

column starts to flash. Fill the next column the

same way.

To move back and forth between the characters,

press the / cursor buttons or press 4or ¢

ENGLISH

(Using the SR4600)

1. Select the desired preset station by pressing theorcursor buttons on the front panel

(Using the remote control unit)

1. Press the 4or ¢ buttons to select the desired preset station, or input your desired preset channel with the numeric buttons on the remote.

CLEARING STORED PRESET STATIONS

You can remove preset stations from the memory using the following procedure.

2.	3.		SET UP/		MENU OFF	3
				1	2
			T.TONE
			PURE DIRECT	AUTO		DTS
		2.	NIGHT	CSII	EX/ES	VIRTUAL
				7	8	9
				4	5	6
			DISPLAY	MCH-ST	STEREO	7.1CH IN

SURROUND	CLEAR	MEMO	A/D	P.SCAN/V-OFF
DIGITAL			0
AAC
			CHANNEL/SKIP

3.	BASS	TREBLE	TUNE/SEARCH
		T-MODE	RDS	F.DIRECT

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation.

4.5. 2. 5. 6.

AV SURROUND RECEIVER SR4600

buttons on the remote.

Note:

• Unused columns should be filled by entering

blanks.

6. To save the name, press the MEMO button on

the front panel or remote for more than 2

seconds.

Ten keypad Press, press again, press again, etc.

1	A → B → C → 1 → A
2	D → E → F → 2 → D
3	G → H → I → 3 → G

INPUT/DISC+ AUDIO SUB-T/ATT PTY

CH.SEL LIP.SYNC

4	J → K → L → 4 → J
5	M → N → O → 5 → M

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMO button on the front panel or press the MEMO button on the remote.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Note:

•To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds.

5.	OSD		MENU
		ENTER
5.	SET UP/		MENU OFF
	T.TONE
	PURE DIRECT	AUTO		DTS
		1	2	3
2. 5. 6.	NIGHT	CSII	EX/ES	VIRTUAL
		7	8	9
		4	5	6
	DISPLAY	MCH-ST	STEREO	7.1CH IN
	CLEAR	MEMO	A/D	P.SCAN/V-OFF
			0
			CHANNEL/SKIP
5.	BASS	TREBLE	TUNE/SEARCH
		T-MODE RDS F.DIRECT
4.	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY
	CH.SEL			LIP.SYNC

6	P → Q → R → 6 → P
7	S → T → U → 7 → S
8	V → W → X → 8 → V
9	Y → Z → space → 9 → Y

0 – → + → / → 0

31