Homelite CSP4518 - UT74125D, CSP4520 - UT74127D Warranty, Guarantee Statement Rtsa / Rtuk / RTG

Page 19

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

Engine starts, runs,

Carburettor requires adjustment.

Turn idling speed screw “T” clockwise to increase idling

and accelerates but will

 

speed. If chain turns at idle, turn idling speed screw “T”

not idle.

 

anticlockwise to decrease speed. Wear protective

 

 

equipment and observe all safety instructions. See

 

 

Figure 24.

 

 

 

Engine starts and runs,

1.

Chain oil tank empty.

but chain is not rotating.

2.

Check chain tension for overtight

 

 

 

condition.

 

3.

Check for oiler function.

1.Oil tank should be filled every time that fuel tank is filled.

2.Tension chain per instructions in “Maintenance – Adjusting the Chain Tension” earlier in this manual.

3.Run at half throttle 30 to 45 seconds. Stop saw and check for oil dripping from SAFE-T-TIP® and guide bar. If oil is present the chain may be dull or bar may be damaged. If no oil is on the SAFE-T-TIP®, contact a Homelite service dealer.

Bar and chain running hot and smoking.

1.Chain brake engaged.

2.Chain tension too tight.

3.Check guide bar and chain assembly.

4.Check guide bar and chain for damage.

1.Release chain brake, refer to “Operation – Operating Chain Brake” earlier in this manual.

2.Tension chain per instructions in “Maintenance – Adjusting the Chain Tension” earlier in this manual.

3.Refer to “Maintenance – Assembling the Bar and Chain” earlier in this manual.

4.Inspect guide bar and chain for damage.

NOTE: The carburettor adjustment needle(s) are equipped with plastic cap(s) which prevent anticlockwise rotation from the original factory adjustment. If your product exhibits specific performance problem(s) where the Troubleshooting Section recommends an anticlockwise needle adjustment and you have made no adjustments since the original purchase, take the product to a factory authorised service dealer for repair. In most cases, the needed adjustment is a simple task for the factory trained service representative.

WARRANTY

GUARANTEE – STATEMENT

(RTSA / RTUK / RTG)

All Homelite products are guaranteed from defects in material and workmanship, for a period of twenty-four (24) months, effective and evidenced from date of original invoice or delivery note.

Defects caused by normal wear and tear, unauthorised/improper maintenance/handling or overload are excluded from this guarantee as are accessories such as battery packs, bulbs, blades and bits, etc.

In the event of malfunction within the guarantee period, please return the assembled product with proof of purchase to your dealer or nearest Homelite Service Centre.

Your statutory rights in respect of defective products remain unaffected by the warranty.

Ryobi Technologies GmbH, Itterpark 7, D-40724 Hilden, Germany

Ryobi Technologies, Customer Services, Anvil House, Tuns Lane, Henley-on-Thames, RG9 1SA, UK Homelite / R.T.S.A, BP 50012 - 95945 Roissy CDG Cedex – FRANCE

Ryobi Technologies Australia PTY Limited, 359-361 Horsley Road, Milperra, NSW 2214 Australia

UK - Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesGeneral Precautions Specific Safety RulesRefuelling do not Smoke Proper Clothing for SafetyMaintenance Precautions Basic Precautions in the CUTTING/ Work AreaSymbol Name Explanation SymbolsSpecifications Guide Bars FeaturesUnderstanding Your Chainsaw Safety Devices OperationHandling the Fuel Safely KICK-BACK PrecautionsFuel and Refuelling Chain OIL SystemStopping the Engine Starting the EnginePreparing for Cutting Push and Pull Basic OPERATING/CUTTING ProceduresWork Area Precautions Adjusting the CarburettorFelling Trees Hazardous Conditions Adjusting Idling SpeedProper Procedure for Tree Felling Operating the Chain BrakeBucking Removing Buttress RootsLimbing and Pruning Assembling the BAR and Chain MaintenanceAdjusting the Chain Tension Cutting Spring PolesSide Plate Angle Chain MaintenanceSharpening the Cutters TOP Plate Filing AngleMounting the SAFE-T-TIP Nose Guard Cleaning the AIR FilterMaintaining the Guide BAR Maintaining the SAFE-T-TIP Nose GuardChecking the Fuel Filter Cleaning the Starter UnitCleaning the Engine Cleaning the Spark Arresting SilencerBAR and Chain Combinations TroubleshootingStoring the Chainsaw 1 Month or Longer Guarantee Statement Rtsa / Rtuk / RTG WarrantyProblem Possible Cause Solution EC Declaration of Conformity Safety Directive

CSP3816 - UT74123D, CSP4518 - UT74125D, CSP4520 - UT74127D specifications

The Homelite CSP series of chainsaws, including the CSP4520 - UT74127D, CSP4518 - UT74125D, and CSP3816 - UT74123D, exemplifies innovation and efficiency in the world of outdoor power equipment. Recognized for their user-friendly design, these chainsaws are tailored for both novice users and seasoned professionals, delivering performance and reliability across a range of cutting tasks.

The CSP4520 model features a robust 20-inch bar and chain, making it ideal for tackling larger jobs, such as felling trees and cutting firewood. Its powerful motor ensures consistent performance, while the lightweight design reduces fatigue during extended use. The inclusion of an automatic chain oiler enhances longevity and smooth operation, ensuring that the chain operates fluidly and efficiently.

The CSP4518, with its 18-inch bar, offers a balance of power and maneuverability. This chainsaw is perfect for homeowners and landscapers who need to perform pruning, trimming, and light cutting tasks. The tool-less chain tensioning feature simplifies adjustments, making it easy for users to maintain optimal performance without the need for additional tools. Additionally, the ergonomic handle design provides comfort and control, allowing for precise cutting.

Meanwhile, the CSP3816 model, featuring a 16-inch bar, is designed for light-duty applications. It is an excellent choice for users who require a compact and agile chainsaw for trimming branches and cutting small logs. This model is particularly praised for its easy-start technology, which minimizes pull effort, making it accessible for users of all skill levels. The onboard safety features, including a chain brake and low kickback chain, enhance user safety during operation.

Each of these models incorporates electrifying technologies that contribute to their performance. The Homelite CSP series utilizes a combination of powerful motors, advanced chain mechanisms, and effective safety systems to ensure a smooth cutting experience. Built with durability in mind, these chainsaws are constructed from high-quality materials that withstand the rigors of outdoor use.

In conclusion, the Homelite CSP4520, CSP4518, and CSP3816 chainsaws showcase the perfect blend of power, efficiency, and safety features. Whether for heavy-duty logging or light pruning, these models offer versatility and ease of use, making them a valuable addition to any outdoor toolkit. With their performance-driven design and thoughtful engineering, they stand out in the competitive chainsaw market, appealing to both casual users and professionals alike.
Top Page Image Contents